ジョブル List of Products and Services

The XE10-110 kit A is a set that includes one indoor 1-port transmitter "XE10-110-TX" from the EPoC (Ethernet & Power over Coaxial) series and one indoor 1-port receiver "XE10-110-RX" powered by an adapter.

• Security cameras and surveillance systems
• Other security systems
• others

The IP09CK is a coaxial cable long-distance transmitter that can extend Ethernet up to 1,000 meters, typically up to 100 meters. By combining it with its sister product "IP09," it allows for a mix of coaxial and LAN cables, enabling further extension. Additionally, it supports low power consumption with EEE (Energy-Efficient Ethernet). It has a built-in surge protector for safe use. - Long-distance transmission of Ethernet using coaxial cables of 5C-2V or higher - Maximum extension of 500 meters at 100 Mbps and 1,000 meters at 10 Mbps (for 5C-FB) - Compatible with 10BASE-T/100BASE-TX/100BASE-T1 - Supports EEE (Energy-Efficient Ethernet) - Built-in surge protector

• Other security systems
• Other PCs and OA equipment
• others

This is a transmitter that extends VGA (analog RGB), USB 2.0, audio, infrared remote control signals, and RS232C up to 140 meters using CAT5e or CAT6 LAN cables (UTP/STP 24AWG solid wire). The transmitter allows for loop output of the VGA signal, enabling video confirmation near the VGA output device.

• Other commercial buildings and service facilities
• Other PCs and OA equipment
• others

The IP09K is a product that enables long-distance Ethernet transmission with a single LAN cable. The IP09K is a set of two units of the IP09, which functions as both a transmitter and a receiver. It is primarily used for one-to-one connections, but it can also be used as a repeater, allowing for distance extension with each additional unit (individual sales of the IP09 are also available). - For one-to-one connections, it can extend up to 500m at 100Mbps and up to 800m at 10Mbps. - It supports low power consumption with EEE. - It has a built-in surge protector (with a withstand voltage of 1.5kV).

• others
• Other PCs and OA equipment
• Other security systems

The 2E10-110-TX is an EPo2 (Ethernet & Power over 2 wires) transmitter (TX) with one PoE Plus compatible LAN port. It operates using Po2 power from an EPo2 receiver located up to 600 meters away via two-wire cables such as telephone lines or UTP/STP, transmitting Ethernet and power to connected devices like cameras. It enables the construction of intercoms, elevator cameras, surveillance systems, etc., using existing telephone lines.

• Security cameras and surveillance systems
• Other security systems
• others

The VDS6500A is a camera transmission device that can transmit 2-channel video signals, power, and UTC signals over long distances using a single coaxial cable. It supports four types of video signals: AHD, HD-TVI, HDCVI, and Composite (NTSC/PAL). Each of the two channels is compatible with UTC (Up-the-Coax), allowing for individual control of two cameras. * CH1 and CH2 can each accept different video signals (mixed signals are possible). * UTC is not compatible with all cameras. If you are using it for the first time, please contact us in advance. - Long-distance multiplex transmission of 2-channel video signals, power, and UTC signals using a single coaxial cable. - Capable of supplying a total maximum power of 4A at DC12V (up to 2.5A individually). - Easy to change/add existing cameras. - The transmitted video signals can be mixed. - RF modulation transmission that is resistant to noise. * The VDS6500A is not compatible with the VDS6500 (discontinued product).

• Security cameras and surveillance systems
• Other security systems
• others

The JCP-101HD is a transmitter that multiplexes 2-channel AHD/HD-TVI/HDCVI/composite video signals (which can be mixed) and transmits them over a single coaxial cable. One of the two channels is transmitted in baseband, while the other channel is transmitted via RF modulation. It is effective for updating or adding cameras using existing cameras and coaxial cables.

• Security cameras and surveillance systems
• Other security systems
• others

The EPoC series is a PoE Plus compatible IP long-distance coaxial cable transmission device that can transmit Ethernet and power (PoE) over a single coaxial cable for long distances. It extends the transmission distance, which is limited to 100m with standard Ethernet, up to 1,200m (using 5C-2V or higher) without the need for repeaters or other devices in between. We offer indoor models as well as outdoor transmission devices that are waterproof and equipped with lightning protection. 【Features】 ■ Achieves long-distance Ethernet transmission at a lower cost than fiber optics ■ A rich lineup allows for flexible and free system construction ■ Supports the introduction of new systems while utilizing existing wiring and equipment *For more details, please refer to the PDF materials or feel free to contact us.

• Security cameras and surveillance systems
• Other commercial buildings and service facilities
• others

The SEAT-type surge protector JUP480F protects equipment from surge damage by absorbing surge energy internally. The absorbed energy is slowly released through the ground line. It can be easily added to an AC power cable in parallel, eliminating the need to cut the wires. Since there are no specific requirements for ground resistance, it is effective in protecting equipment in environments with poor grounding.

• Lightning protection
• Other security systems
• others

The SEAT method surge protector J1S-320V removes surges from AC power lines simply by connecting it to an AC power outlet. - Surge protector compatible with AC 100-320V 50Hz/60Hz - Protects devices from various surges just by connecting to an AC power outlet Effective against surges caused by chattering and ON/OFF of inductive load circuits, as well as electromagnetic pulses and sparks that conventional lightning arresters cannot eliminate - The surge removal method SEAT (Surge Energy Absorb & Transfer) has been patented in Japan (Patent No. 5192002), as well as in the United States (US 8295024B2), China (ZL 201010111239.8), and Taiwan (I 390816).

• Lightning protection
• Other security systems
• others

- Converts HDMI signals to HD-TVI signals for output (with HDMI video signal loop output). - Input resolutions (HDMI): 800x600, 1024x768, 1280x720, 1280x1024, 1440x900, 1920x1080. - Output resolutions (HD-TVI): 720p 50/60Hz or 1080p 25/30Hz. - The resolution of the HDMI video loop output will match the input HDMI resolution. (Audio will not be output.) - The output resolutions of HD-TVI, 720p and 1080p, can be switched using a switch. - The power LED and operation LED allow for quick understanding of the device's status.

• Video Monitoring System
• Other security systems
• others

The JAHD-ER03HR is a converter that converts HDMI video signals to AHD signals. - Converts HDMI signals to AHD signals - Maximum HDMI input resolution is 1080p (1920x1080) - HD signal output can be selected from 720p or 1080p - Enhances security when using AHD-compatible recorders - HDMI video signal can be looped out (audio is not output) - Allows installation of a monitor without needing an additional HDMI splitter, even if there is only one HDMI output on the device (using loop output) - Used in various scenarios, such as recording the operation screen of a PC that handles important information.

• Security cameras and surveillance systems
• others
• Other security systems

The AD001HD4 converts AHD/HD-TVI/HDCVI/composite video signals to HDMI/VGA/composite video. - Supports AHD/HD-TVI/HDCVI video input at 1080p 25/30Hz and 720p 25/30/50/60Hz, as well as composite video input. - Output options include HDMI, VGA, and composite/loop output. - All three types of signal outputs can be output simultaneously. - In HD input mode, it is possible to input two channels of HD/composite video and switch output/PIP output. *Simultaneous input of AHD and HDCVI is not possible in HD input mode (but combinations with HD-TVI/composite are possible). - HDMI output supports 480p/576p/720p/1080i/1080p. - Composite video output supports NTSC/PAL. - Power adapter included.

• Security cameras and surveillance systems
• others
• Other security systems

- In standard Ethernet, the maximum transmission distance is up to 100m, but it can be extended up to 600m (for 5C-2V or higher) without using repeaters or other devices in between. - It transmits the Ethernet and power (PoE) necessary for the installation of IP cameras using existing coaxial cables. - Up to 4 cameras (RU/R) can be connected to one network device (LU). - Using 5C-2V, it achieves a maximum bidirectional communication speed of up to 100Mbps over a distance of up to 600m. - The link cable connection terminal is equipped with a built-in TVS/GDT (surge absorber/arrestor) to protect the devices from surges.

• Security cameras and surveillance systems

The "PoE/PoE Plus Power Supply Ethernet Repeater" is a product that extends the transmission distance of Ethernet by up to 200m with a single unit. It can connect up to four units between hosts, allowing for a maximum extension of 500m. With a low power consumption of approximately 1.2W, it minimizes attenuation while supplying power to PoE devices. We offer two products in our lineup: "Standard Type" and "IP65 Waterproof and Dustproof Type." It also supports 1000BASE-T, making it suitable for high-capacity data transmission. 【Features】 ■ Supports STP cables/connectors for noise-resistant transmission ■ Extends Ethernet at 10/100/1000M speeds ■ Operates on PoE power, eliminating the need for an additional power supply ■ Wide operating temperature range of -40 to 75°C (Waterproof and Dustproof Type) *For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Internet System

- Ultra-compact 4ch DVR that can be installed anywhere - Supports AHD/HD-TVI (720p/1080p) and composite video (can be mixed) - Capable of recording 4ch mono audio simultaneously with video - Supports recording to HDD/SSD/SD card/USB memory/USB HDD * Recording media such as HDD are optional - Operates on DC 9-36V, making it compatible with a wide range of power sources beyond the included power adapter for vehicles - Low power consumption allows for operation with rechargeable batteries or solar batteries - By connecting an optional GPS antenna (model number: ETGM-5019), automatic time correction and location information recording are possible - Operates in temperatures from -20 to 70°C (when recording to SD card), suitable for installation in outdoor waterproof boxes - Back up recorded video to SD card/USB memory/USB HDD - Backed-up recorded video can be played on a Windows PC (playback software included)

• Security cameras and surveillance systems
• others
• Other store equipment and supplies

The HE01ERK transmits HDMI signals over LAN cables up to 40 meters (1080p). It is convenient for displaying PC or DVR video on a monitor located a short distance away. - Transmits HDMI (up to 1920x1200) over a single CAT5e/6 cable (CAT6 or higher recommended). * For longer distances, the HE03 (HDCP compliant) can transmit up to 150 meters. - Both ends of the transmission cable use RJ45, and commercially available LAN cables (straight wiring) can be used. - Operates on power supplied from the HDMI port. - Not HDCP compliant. - Includes HE01SET (transmitter) and HE01SER (receiver), and a DC jack to micro USB conversion cable. * DDC communication is not supported. EDID outputs a temporary signal registered in the HE01SET. * If the input HDMI signal level is low, the transmission distance may be reduced. * The power for this device is obtained from the HDMI port of the video output device. If the supplied power is insufficient for normal operation, please provide power to the HE01SET using a USB or a separately sold DC 5V power adapter (LTE10UW-S1-BS33).

• Other security systems
• Other PCs and OA equipment
• others

Our company offers a wide range of "AHD/HD-TVI compatible compact LCD monitors." They support high-resolution analog video display and can also accept composite video input. We have a diverse selection of products, from lightweight plastic-cased wide LCD monitors to high-resolution LCD monitors with metal casings. 【Product Introduction】 "AHD/HD-TVI and Composite Video Input Compatible LCD Monitor" Features a lightweight plastic casing. "AHD/HD-TVI, Composite Video, and VGA Input Compatible Metal Casing LCD Monitor" VGA input compatible with video display from PCs, recorders, etc. "AHD/HD-TVI, Composite Video, HDMI, and VGA Input Compatible Metal Casing LCD Monitor" Supports PIP function to display two videos simultaneously. "AHD/HD-TVI, HDMI, DVI, and VGA Input Compatible Metal Casing LCD Monitor" 15.6-inch wide, with a resolution of 1920×1080, clearly displays 1080p video. "AHD/HD-TVI and Composite Video Input Compatible Rechargeable Test Monitor" Automatically detects and displays NTSC and PAL video. *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

• Video Monitoring System

The HE03 transmits HDMI signals over LAN cables (CAT5e/6/7 UTP/STP 24AWG) for long distances. The maximum supported resolution is 1080p 60Hz and 1920✕1200 60Hz. The HE03T (transmitter) can loop output the HDMI input signal, allowing for video display on a local monitor without using a splitter near the HDMI output device. Package contents: HE03T x1, HE03R x1, power adapter x2.

• Security cameras and surveillance systems
• Other PCs and OA equipment
• others

JPX201 / JIPX201 (waterproof type) is an Ethernet repeater that supports 10/100/1000M PoE/PoE Plus power receiving. It operates by receiving PoE or PoE Plus and extends Ethernet up to 200m. Additionally, it can connect up to 4 devices, allowing for an extension of up to 500m. It is capable of supplying power to devices compatible with PoE or PoE Plus.

• Video Monitoring System

- A single coaxial cable, whether existing or newly installed, transmits AHD or composite (NTSC/PAL) video signals along with camera power in a superimposed manner. - AHD supports 720p and 1080p, allowing for the transmission of high-resolution HD quality video. - For 5C-FB cables, power transmission of DC12V 1A is possible up to 800m, and 1.5A up to 500m. - For 5C-2V cables, power transmission is possible up to 600m (0.9A), and for 3C-2V cables, up to 300m (0.8A). - Modulating and transmitting AHD/composite video is effective for noise countermeasures in cases where noise occurs during normal transmission. - The power can also be used for devices other than the camera, allowing for the installation of DC12V equipment.

• Security cameras and surveillance systems
• Other security systems
• others

- Transmits USB over CAT5e/6 cable up to 60m. - Compatible with USB 2.0 (High-Speed) and USB 1.1 (Low-Speed/Full-Speed). - Transmits between UE03T (USB device side) and UE03R (PC side). - UE03T (USB device side) has a 4-port USB hub function. - UE03R (PC side) receives power from the USB port, so no power adapter is needed. - Supports imaging devices such as printers and USB cameras, in addition to mice and keyboards. - Set includes UE03T, UE03R, and power adapter (for UE03T).

• Other PCs and OA equipment
• Other security systems
• others

The HD02-4K is a splitter that outputs one HDMI signal to two outputs. - Supports up to 4K 30Hz video - EDID supports built-in/signal pass-through/recording - Maximum signal bandwidth for HDMI signals is up to 10.2Gbps - Audio supports LPCM 7.1 192kHz, Dolby TrueHD, and DTS-HD MA (pass-through) - Supports HDCP 1.4 - Power adapter included

• Other security systems
• Other commercial buildings and service facilities
• others

MLT4-B1-1-100 is a surge protector compatible with power supplies and control signals, contact signals, etc., up to DC100V. - No grounding work is required to protect equipment from various surges. It blocks surges from power wiring and surges caused by electromagnetic pulses. It is also effective against surges caused by chattering and the OFF state of inductive load circuits, which cannot be eliminated by conventional lightning protectors.

• Other security systems
• Lightning protection
• others

The surge protector JSPAW-CH-6-250 for AC power supplies protects equipment from high voltage surges caused by induced lightning and other sources that enter power wiring for outdoor installations. It also blocks surges caused by induced lightning, switching, inrush current, and electromagnetic pulses.

• Lightning protection
• Other security systems
• others

SDIVPD extends HD-SDI signals up to 300 meters using a single coaxial cable (when using 5C-FB). It also allows for the combined transmission of camera power and RS485 signals. It can supply up to 2A of DC12V power to the camera, making it effective for connecting to cameras with relatively high power consumption.

• Other security systems

EP01 is a power supply adapter that uses the spare wires of a 10/100M Ethernet (LAN cable) to provide power. - It transmits power using two unused pairs in the 10/100M LAN wiring. - Since you can freely choose the power supply, it can power various non-PoE devices. - It can be used not only for power supply but also for transmitting contact signals and RS485 signals. * It is used by modifying the power adapter included with the network device. * It cannot be used with 1000BASE LAN. * The transmission distance varies depending on the power consumption of the power adapter and device, as well as the quality of the cable.

• Internet System

The HE02EI is an HDMI transmitter that extends HDMI and infrared remote control signals up to 70 meters (1080p/60Hz CAT6a) using a single LAN cable. It allows you to display content from gaming consoles, Blu-ray players, and HD television sources on AV amplifiers or HD televisions located at a distance. The direction of infrared transmission can be switched between "transmitter to receiver" or "receiver to transmitter."

• Other PCs and OA equipment
• Other security systems
• others

The SDI02 is a converter that converts HDMI signals to SDI signals. It converts HDMI output signals from devices such as digital video recorders (DVRs) into SDI signals. You can input HDMI output camera footage or the HDMI output screen from a DVR into an SDI switcher or SDI recorder. *Please note that HDCP is not supported. If you input a signal that supports HDCP, such as from consumer DVD/BD players, it will not be converted and output to SDI. The SDI signal supports not only SD-SDI/HD-SDI but also 3G-SDI signals at 1080p 60Hz. It converts HDMI audio signals to SDI embedded audio. The HDMI audio signals support LPCM 2ch and LPCM 7.1ch surround sound.

• Other security systems
• Security cameras and surveillance systems
• others

SW105 is a 5-port Ethernet switch for network cameras. Out of the 5 ports, 4 ports support PoE Plus power supply. PoE power supply can provide up to 39W per port, with a total maximum of 75W across 4 ports. Transmission is possible up to 200m with LAN cables (CAT6 or higher).

• Other security systems

MLT4-B1-1-12 is a surge protector compatible with power supplies and control signals up to DC12V, including contact signals. - No grounding work is required to protect devices from various surges. It blocks surges from power wiring and surges caused by electromagnetic pulses. It is also effective against surges caused by chattering and the OFF state of inductive load circuits, which cannot be eliminated by conventional lightning arresters.

• Lightning protection
• Other security systems
• others

The SDI04D is an SDI signal distributor that outputs 4 copies of SD/HD/3G-SDI signals. - The SDI signal input to the distributor is corrected and output using reclocking and equalization functions, allowing for the re-extension of signals transmitted over long distances. * Reclocking function: A function that removes jitter (fluctuation) from the signal by reconstructing the clock, returning it to accurate timing. * Equalization function: A function that corrects waveform distortion caused by transmission, restoring it to a clean waveform. - It supports 7.1 channel audio.

• Security devices
• Security cameras and surveillance systems
• others

The IPC-600P can transmit PoE/PoE Plus Ethernet over coaxial cable up to 600 meters. Additionally, it achieves a communication speed of up to 100 Mbps in the direction from the camera to the Ethernet switch (monitor side), allowing for smooth transmission of high-resolution IP camera footage with large data volumes. Furthermore, by connecting a camera-specific switch SW105 or a DC 56V power adapter to the IPC-600P-T on the monitor side, it is also possible to supply up to 25.5W (5C-2V 100m) to the camera. This is effective for connecting IP cameras to remote locations such as outdoors or for upgrading from existing analog cameras to IP cameras.

• Security cameras and surveillance systems
• others
• Other security systems

- Surge protector compatible with 10/100BASE Ethernet wiring - Supports power supply via PoE and PoE Plus - Protects devices from various surges without the need for grounding, including induced lightning (LFS), power switching surges (PSS), inrush current (SIC), and electromagnetic pulses (EMP) - Passed testing with combination waveforms (1.2/50μs, 8/20μs) at 6kV/3kA - Complies with IEC standard "IEC 61643-21," equivalent to "JIS C5381-21" (surge protective devices connected to communication and signal circuits, Category C2 equivalent) - Complies with IEC standard "IEC 61000-4-4," equivalent to "JIS C1000-4-4" - New method of accumulating surges without discharging to ground and releasing them gradually (between pins 1-2, 3-6) with patents obtained in Japan (patent number 5192002), the USA, China, and Taiwan * Protection for the power system between pins 4/5-7/8 is provided by conventional varistors. - DIN rail adapter included

• Security cameras and surveillance systems
• Lightning protection
• others

PC1A is a DC 12V output voltage converter that converts an AC/DC power supply of 18V or higher to DC 12V. It is ideal for supplying DC 12V to cameras and other devices when transmitting over long distances with AC/DC 24V. It can supply power up to DC 12V 1A (12W).

• Other security systems
• DC Power Supply
• others

The PC500 is a DC 12V output voltage converter that converts a power supply of AC/DC 15V or higher to DC 12V. It is ideal for supplying DC 12V to cameras and other devices when transmitting over long distances with AC/DC 24V. It can provide a power supply of up to DC 12V/500mA (6.0W).

• Other security systems
• DC Power Supply
• others

DR01 is a repeater that can extend DVI-D signals (single link) up to 50 meters using a DVI cable. It supports input signals of DVI-D up to 1080p or 1920✕1200.

• Other security systems

PoE/PoE Plus Ethernet is transmitted using coaxial cables. The transmission distance of standard PoE Ethernet can be extended from the maximum of 100m to up to 300m. Since it transmits by connecting at both ends of the transmission cable, it can be used in places where relay devices cannot be installed, such as overhead wiring or underground burial. By using PoE Plus (IEEE802.3at) switches or injectors, it can supply up to 14W of power to receiving devices such as IP cameras. The operating temperature range is wide, from -10 to 60°C, allowing it to be used in harsh temperature environments.

• Other security systems
• Security cameras and surveillance systems
• others

The SP016P simultaneously protects LAN wiring that includes PoE/PoE Plus power supply for up to 16 systems at 10/100/1000M. It diverts high voltage surges caused by induced lightning and other sources away from the equipment to the ground before it reaches the devices. The surge protector should be installed as close as possible to the equipment that needs protection. When protecting a camera, it should be placed near the camera; when protecting a monitor or NVR/server, it should be installed near the monitor/DVR/server. The basic principle of surge protection is to install protectors on both the camera side and the display device (monitor) side. If the SP016P is installed on the monitor side, additional devices such as the IP06PH or JPOE-B2-1, SP006P can be installed on the camera side for each camera wiring system.

• Internet System
• Lightning protection
• others

HVY01 is a converter that converts HDMI (or DVI-D) to VGA (analog RGB) or component video with analog stereo audio. (Output resolution can be changed) * If connecting DVI-D, please prepare a DVI to HDMI conversion adapter separately. - Maximum resolution: VGA (analog RGB): 1920✕1200, Component: 1080p - Supports 2-channel audio output (stereo) - Settings via OSD (on-screen display) - Power adapter included * Not HDCP compliant

• Other security systems

The DE02E can transmit DVI-D signals over LAN cables up to 100 meters. It can connect monitors located at a distance to PCs or DVR video sources. - Transmits DVI-D (single link) signals up to 100 meters using CAT5e/6/6a/7 UTP/STP cables (CAT6 cables or higher are recommended). - Both ends of the transmission cable can use RJ45 with commercially available LAN cables (straight wiring). - Maximum resolution: 1920x1200. - Supports HDCP 1.4.

• Other security systems
• Other PCs and OA equipment
• others

- Transmits HDMI video and audio signals over a single coaxial cable. - Capable of transmitting 1080p at 60Hz up to 70m with a 5C-FB cable. (720p, 1080i, and 1080p at 30Hz can be transmitted up to 150m) - Supported resolutions are 480i, 576i, 720p, 1080i, and 1080p. - Includes one transmitter, one receiver, and two power adapters. - Daisy chaining for extended transmission is possible (requires an additional HE01CR). - Supports HDMI 7.1CH audio (only LPCM). - Compatible with HDMI 1.3. * Does not support transmission of signals other than video and audio. * Not compatible with HDCP. * The included receiver HE01CR is only one unit. An additional HE01CR (sold separately) is required for further extension.

• Other security systems
• Other commercial buildings and service facilities
• others

This is a converter that converts SD-SDI/HD-SDI/3G-SDI signals transmitted via coaxial cable to HDMI (supports resolutions of 720p, 1080i, and 1080p). • Active Thru Output Function In addition to HDMI output, active thru output is also possible. The SDI signal output can be further extended due to the active thru feature. • Embedded Audio Support It supports embedded audio, allowing video and audio to be transmitted together. 【Transmission Distance Guidelines (when using 5C-FB)】 - SD-SDI (SMTP 259M 270Mbps): Up to 300m - HD-SDI (SMTP 292M 1.45Gbps): Up to 150m - 3G-SDI (SMTP 424M 2.97Gbps): Up to 80m

• Other security systems
• Security cameras and surveillance systems
• others

- It blocks surges that occur in SD/HD/3G-SDI video signals (BNC connection). - It protects equipment from sudden voltage spikes caused by high-voltage surges such as induced lightning. - It can also be used for analog cameras and TV/CATV antenna cables. - With BNC male on one end and BNC female on the other, it can be easily installed on existing wiring. - It allows voltages below DC24V to pass through.

• Other security systems
• Video Monitoring System
• others

- Transmits VGA (analog RGB) up to 100m using a single CAT5e/6 cable. - Maximum transmission distance varies depending on VGA resolution: 640✕480/800✕600: 100m, 1024✕768: 75m, 1280✕1024: 60m. - Passive type, no power supply required. - Built-in virtual DDC in the transmitter to avoid misrecognition of display resolution/frequency. - Set includes VE01P-T (transmitter) and VE01P-R (receiver). - Both ends of the transmission cable use RJ45, compatible with commercially available LAN cables (straight wiring). - Sync mode setting switch (transmitter). - Sync deviation correction due to signal delay during transmission (receiver). * VE01P (= TTP111VGA) does not use power for simple transmission, so color distortion and ghosting may occur depending on the transmitted signal and operating environment. When displaying text or graphics on a PC screen, the above noise may be more noticeable, so the use of sets like VE02ALT and VE02DALS is recommended.

• Other store equipment and supplies