Ultrasonic probe capable of controlling ultrasonic propagation state from 500 Hz to 300 MHz.

Ultrasonic system combining "Ultrasonic Tester NA (10 MHz)" and "Ultrasonic Oscillator (20 MHz)"

An ultrasonic system that allows for easy measurement analysis and oscillation control. The Ultrasonic System Research Institute is publicly conducting experiments using a system that combines the "Ultrasonic Tester NA (recommended type)," which allows for easy measurement analysis of ultrasonic waves, and the "Ultrasonic Oscillation System (20 MHz)," which enables easy oscillation control of ultrasonic waves. Ultrasonic Probe: Overview Specifications - Measurement Range: 0.01 Hz to 200 MHz - Oscillation Range: 0.5 kHz to 25 MHz - Propagation Range: 0.5 kHz to over 900 MHz (confirmed and evaluated through analysis) - Materials: Stainless steel, LCP resin, silicone, Teflon, glass, etc. - Oscillation Equipment Example: Function Generator Note: Ultrasonic Propagation Characteristics 1) Detection of Vibration Modes (Changes in Autocorrelation) 2) Detection of Nonlinear Phenomena (Changes in Bispectrum) 3) Detection of Response Characteristics (Analysis of Impulse Response Characteristics) 4) Detection of Interactions (Analysis of Power Contribution Rates) Note: "R" Free Statistical Processing Language and Environment - autocor: Autocorrelation Analysis Function - bispec: Bispectrum Analysis Function - mulmar: Impulse Response Analysis Function - mulnos: Power Contribution Rate Analysis Function

• Water Treatment
• Other analytical equipment
• others

Ultrasonic oscillation (sweep oscillation) system for controlling nonlinear phenomena

The Ultrasonic System Research Institute has developed a technology to control the nonlinear vibration phenomena of surface elastic waves based on the acoustic characteristics of original ultrasonic probes. The key point is the setting of sweep oscillation conditions using two ultrasonic probes (essentially, it cannot be controlled with just one probe for ultrasonic oscillation control. By combining the oscillation settings of the two probes, the occurrence of resonance phenomena and nonlinear phenomena can be controlled). Resonance phenomena and nonlinear phenomena can be controlled within a frequency range tailored to the intended use. In particular, when strong stimulation is required, this is achieved by utilizing low-frequency resonance phenomena (e.g., breaking glass). When high-frequency stimulation is needed, this is achieved by utilizing high-frequency nonlinear phenomena (e.g., 700 MHz stimulation).

• Vibration and Sound Level Meter
• Scientific Calculation and Simulation Software
• others

An ultrasonic system that easily controls the oscillation of megahertz ultrasound—applying technology to evaluate the propagation characteristics of ultrasonic probes.

The Ultrasonic System Research Institute has developed a technology to control the nonlinear phenomena of surface elastic waves (ultrasonic vibrations) that propagate through the target object, using an original ultrasonic system (sound pressure measurement analysis, oscillation control). **Technology for Controlling Nonlinear Ultrasonic Vibration Phenomena** 1) Control setting technology that adjusts the oscillation output, waveform, and variations of the oscillation control using a function generator, tailored to the acoustic characteristics of the target object. 2) Manufacturing technology for an ultrasonic oscillation control probe that enables control of changes in ultrasonic oscillation voltage, including adjustments to the oscillation surface. 3) Manufacturing technology for an ultrasonic measurement probe that allows for the measurement of changes in ultrasonic vibrations at 100 megahertz, including adjustments to the oscillation surface. 4) Optimization technology for sweep oscillation conditions. Using the above technologies, we control (optimize) the propagation state of ultrasonic waves according to specific objectives. Note: The dynamic control of ultrasonic waves is performed based on the analysis and evaluation of sound pressure data related to nonlinear phenomena, considering the interaction between the acoustic characteristics of the target object and ultrasonic oscillation control. (Sound pressure measurement, analysis, confirmation, and evaluation are conducted using an ultrasonic tester.)

• Analysis and prediction system
• Other measuring instruments
• others

A completely new vibration measurement technology using original products (ultrasonic testers).

The Ultrasonic System Research Institute has developed a completely new <vibration measurement technology> using its original product (ultrasonic tester). The ultrasonic sound pressure measurement analysis technology developed so far applies the "measurement, analysis, and control" technology related to the nonlinear phenomena of ultrasound. From the accumulation of data measuring, analyzing, and evaluating the dynamic characteristics of ultrasound propagating on surfaces, we have developed technology that can <measure, analyze, and evaluate> vibration states from low frequencies (0.001 Hz) to high frequencies (700 MHz). Regarding vibrations and noise from buildings and roads, equipment, devices, walls, piping, desks, handrails... as well as the vibrations at the moment of metal melting during welding and instantaneous vibrations during machining, we have made it possible to respond with vibration control and management based on the measurement and analysis of new vibration phenomena. This is a new method and technology, and various application cases have developed from the analysis results so far. In particular, continuous data collection for a standard measurement time of 72 hours is possible, allowing measurement of low-frequency vibrations and irregularly fluctuating vibrations (maximum measurement can be overwritten over a continuous period of 14 days).

• Non-destructive testing
• Other measuring instruments
• others

We provide on-site services for the measurement, analysis, and evaluation of ultrasonic equipment.

Application of technology to analyze and evaluate the dynamic characteristics of ultrasound The Ultrasound System Research Institute has developed a method (system) for the <analysis, experimentation, and evaluation> of ultrasound, utilizing "measurement, analysis, and control" technology related to the nonlinearity of ultrasound. Using this technology, we conduct <sound pressure measurement, experimentation, analysis, and evaluation> (including on-site support) for ultrasonic cleaning machines. To evaluate the complex and varying usage conditions of ultrasound, we do not rely solely on sound pressure and frequency; instead, we consider "timbre." We analyze it using a time series data autoregressive model and report and propose <evaluation and application> based on statistical models.

• pump
• Turbid water and muddy water treatment machines
• Manufacturing Technology

Surface modification treatment using ultrasonic propagation control above 200 MHz.

The Ultrasonic System Research Institute has made it possible to control the nonlinear propagation of ultrasound by analyzing and applying measurement, analysis, and control techniques related to the propagation state of ultrasound as the acoustic characteristics of the target object. As a result, we have developed a technology that efficiently alleviates residual stress on the surface of components and homogenizes the entire surface. This technology for alleviating surface residual stress improves the fatigue strength against metal fatigue and achieves uniformity in various surface treatments. In particular, by considering the guided waves (surface elastic waves) of the target object in the setting and control of the ultrasound propagation state, we have developed control methods, tools, and systems that realize effective dynamic changes in the target object as a stimulus within a certain range that includes nonlinear phenomena. We have confirmed a wide range of effects on various surfaces of metal parts, plastic parts, and powder materials. This is a new surface treatment technology using ultrasound, which, including the general effects based on acoustic characteristics, can be utilized and developed as a distinctive inherent operational technology for the development of new materials, stirring, dispersion, cleaning, and chemical reaction experiments.

• Water Treatment
• Other measuring instruments
• others

Ultrasonic control technology based on the classification of nonlinear phenomena in which ultrasonic vibrations propagate.

The Ultrasonic System Research Institute has developed a classification method for the phenomenon of ultrasonic vibration propagation by analyzing measurement data of ultrasonic propagation states using bispectral analysis. The method developed in this instance estimates the linear and nonlinear resonance effects based on the dynamic characteristics (changes in nonlinear phenomena) of the main frequencies (power spectrum) related to the ultrasonic propagation state. From previous data analysis, we have been able to classify effective utilization methods into the following four types: 1: Linear type 2: Nonlinear type 3: Mixed type 4: Variable type There are numerous successful cases of device development and control settings based on each of the above types. This technology will be offered as a consulting service. Ultrasonic propagation characteristics: 1) Detection of vibration modes (changes in autocorrelation) 2) Detection of nonlinear phenomena (changes in bispectrum) 3) Detection of response characteristics (analysis of impulse response) 4) Detection of interactions (analysis of power contribution rates) Note: The following tools will be used for analysis. Note: "R" is a free statistical processing language and environment.

• Other Software

Technology to control low-frequency resonance phenomena and high-frequency nonlinear phenomena.

The Ultrasonic System Research Institute has developed technology to manufacture ultrasonic probes that can control ultrasonic propagation states from 500 Hz to over 500 MHz, tailored to specific applications. Ultrasonic Probe: Overview Specifications Measurement Range: 0.01 Hz to 200 MHz Oscillation Range: 1.0 kHz to 25 MHz Propagation Range: 0.5 kHz to over 900 MHz (confirmed through acoustic pressure data analysis) Materials: Stainless steel, LCP resin, silicon, Teflon, glass, etc. Oscillation Equipment: Example - Function Generator By understanding the acoustic properties of metals, resins, glass, etc., and through oscillation control, we achieve propagation states tailored to specific purposes regarding acoustic pressure levels, frequencies, and dynamic characteristics. This is a new foundational technology for precision cleaning, processing, stirring, and inspection based on measurement, analysis, and evaluation techniques for ultrasonic propagation states. By utilizing the acoustic properties of various materials, ultrasonic stimulation can be controlled for structures and machine tools weighing several tons, even in a 3000-liter water tank, with ultrasonic output below 20 W. It was developed as an application method for nonlinear phenomena through an engineering (experimental and technical) perspective on elastic waves and an abstract algebraic ultrasonic model.

• Water Treatment
• Other measuring instruments
• others

An article has been published about the case of introducing the expense reimbursement system "Rakuraku Seisan" at TSP Corporation. ~ In the case of TSP ~ Before the introduction, there were challenges such as dealing with the "paper" sent from various locations and the reliance on specific individuals for the tasks. After the introduction, the input and checking of FB data, which used to take 2 to 3 hours, can now be completed in just 5 minutes. Additionally, the mindset of the accounting department, which was previously reliant on manual entry, has changed. [Case Overview] ■ Challenges before introduction - Dealing with "paper" sent from various locations, reliance on specific individuals ■ Key points of introduction - A robust support system for setup and operation - Easy to start from a small scale both financially and functionally *For more details, please refer to the related links or feel free to contact us.

The facility operating the nurse call system has made the bed exit sensor wireless, allowing it to notify in conjunction with the nurse call. By simply connecting the mat sensor "Foldable Thin Matt-kun," the body movement call "Ugo-kun," and the wheelchair body movement call "Ayumi-chan" to the transmitter HB-RS, you can make the bed exit sensor wireless. The infrared sensor "Just Place Pole-kun" has the transmitter HB-RS built-in. 【Features】 ○ Wireless conversion by simply connecting existing sensors to the transmitter HB-WSK. ○ The bed exit sensor notifies wirelessly in conjunction with the nurse call. ○ Up to 5 transmitters can be registered with one receiver. ○ The communication distance between the transmitter and receiver is approximately 10 meters. ◎ For more details, please contact us or download the catalog.

Full and empty management refers to the real-time display of parking availability and the management of efficient use of parking spaces. By utilizing Hotron's sensors, drivers can quickly discover available parking spaces, achieving efficient parking lot operations. ■ For large parking lots, the "floor management method" and "block management method," which focus on cost reduction, are recommended. Sensors are installed at regular intervals to count the number of vehicles passing through. This method offers the advantage of easy installation and low costs. 【Target Products】 - Vehicle Count Sensor CCS2 - Ultrasonic Sensor HM-UX2/UW2 ■ For smaller scale operations, the "space management method," which installs sensors in each parking space to display availability with high accuracy, is recommended. By ensuring accurate full and empty displays, it helps prevent unnecessary entry of new vehicles and enables safe parking lot operations. 【Target Products】 - Occupancy Detection Sensor HM-UX2/UW2 - Occupancy/Pass Detection Sensor HM-LC6 - Occupancy Detection Sensor HM-LC7/LC7-FLS - Occupancy/Pass Detection Sensor HM-S6 - Occupancy Detection Sensor HM-S8

Castem Co., Ltd. will exhibit at the "Monozukuri World Osaka - Mechanical Components Technology Exhibition" held at Intex Osaka from Wednesday, October 1 to Friday, October 3, 2025. We will showcase lost-wax precision casting and MIM (Metal Injection Molding) products, as well as introduce our new technology, mold-less casting "Digital Cast." In addition to our popular casting demonstrations, we will present case studies on solving issues related to metal parts. Please utilize our "Technical Consultation Booth" to learn about optimal manufacturing methods tailored to your needs, from ultra-small lots to mass production. 【Exhibition Overview】 Dates: October 1 (Wed) - October 3 (Fri), 2025, 10:00 AM - 5:00 PM Venue: Intex Osaka (1-5-102 Nanko-Kita, Suminoe-ku, Osaka City, Osaka Prefecture) Exhibition Booth Number: Hall 6, B Hall 51-1 Pre-registration allows for smooth entry. It is convenient to register via the URL below before your visit. We sincerely look forward to your attendance. https://www.manufacturing-world.jp/osaka/ja-jp/register.html?code=1431877272389396-VEK

From November 11, 2025 (Tuesday), at Pacifico Yokohama, we will be exhibiting at interOpto2025 / Light and Laser Science and Technology Fair (organized by the Optical Industry Technology Promotion Association / Optronics Corporation) with a focus on: - UV-transmitting glass that can be molded - Diffusion glass that can uniformly diffuse incident light - A double-sided lens array that is molded without lamination 【About the Exhibition】 Event Name: interOpto2025 / Light and Laser Science and Technology Fair UV Fair Date: November 11 (Tuesday) to 13 (Thursday), 2025 Opening Hours: 10:00 AM to 5:00 PM Venue: Pacifico Yokohama Exhibition Hall C Booth Number: C-15 Organizer: Optical Industry Technology Promotion Association / Optronics Corporation Official Website: https://www.optronics.co.jp/interopto/ We invite everyone attending this exhibition to visit our booth "Gosuzumi Seiko Glass." We sincerely look forward to meeting you on-site.