▼△▼Update▼△▼ We have updated the DAQ for the powerful air conveyor ejector.▼△▼△▼△

High-speed air conveyor that does not require a vacuum tank, etc.

The powerful air conveyor, the ejector, is a suction device (pump) that operates as a high-speed air conveyor without the need for a vacuum tank or similar equipment. [Additional Explanation] ◆ The recommended type of ejector varies depending on the type and condition of the material being conveyed. When considering a purchase, please inform us of your requirements using the "Quotation Request Form" in the catalog to avoid any issues. ◆ Due to significant fluctuations in the prices of materials used (such as stainless steel), please request a quote each time. ◆ The number following "JT" generally indicates the diameter of the suction side. (There may be slight discrepancies between the model number and actual size due to differences in size expressions like inches.) ◆ As a guideline for selecting a model, choosing one where the conveyed material is about half to one-third of the diameter can be a good reference. ◆ The ejector is not well-suited for conveying highly viscous materials. ◆ It is not effective for conveying materials that solidify upon gripping, but it can convey such materials if they are mixed with more fluid ones. (Note: Materials with a shake-level viscosity can be conveyed, but mortar solidifies inside and is difficult to clean, so it is not recommended.) Further explanations are available in the basic information section.

• Earth retaining wall/foundation reinforcement
• Earthworks
• Pile and foundation work

Instantly crush soil and sand with high-speed air! It is possible to excavate soil and sand without damaging the target object!

The Air Schop is a device that uses compressed air ejected from a special nozzle to excavate (loosen) hardened soil and debris. It can spray air at high speed from the tip, instantly crushing the debris, allowing for excavation without damaging the target object. 【For the safety of the operator (soil and debris may scatter during operation.)】 ■ During operation, please ensure to wear earplugs and goggles, as well as protective gear for your body. * For facial protection, please wear thick canvas or leather gloves, an apron, or equivalent gear to protect against scattering. ■ You must have basic knowledge of the safe use of air compressors. ■ When connecting compressed air, never point the Air Schop's outlet at a person, look into it, or allow anyone to look into it. (This can cause injury.) ■ Proper use will have no impact on the environment. * For more details, please request materials or view the PDF data available for download.

• Earthworks
• Pile and foundation work
• Drilling Machine

An article has been published about the case of introducing the expense reimbursement system "Rakuraku Seisan" at TSP Corporation. ~ In the case of TSP ~ Before the introduction, there were challenges such as dealing with the "paper" sent from various locations and the reliance on specific individuals for the tasks. After the introduction, the input and checking of FB data, which used to take 2 to 3 hours, can now be completed in just 5 minutes. Additionally, the mindset of the accounting department, which was previously reliant on manual entry, has changed. [Case Overview] ■ Challenges before introduction - Dealing with "paper" sent from various locations, reliance on specific individuals ■ Key points of introduction - A robust support system for setup and operation - Easy to start from a small scale both financially and functionally *For more details, please refer to the related links or feel free to contact us.

The facility operating the nurse call system has made the bed exit sensor wireless, allowing it to notify in conjunction with the nurse call. By simply connecting the mat sensor "Foldable Thin Matt-kun," the body movement call "Ugo-kun," and the wheelchair body movement call "Ayumi-chan" to the transmitter HB-RS, you can make the bed exit sensor wireless. The infrared sensor "Just Place Pole-kun" has the transmitter HB-RS built-in. 【Features】 ○ Wireless conversion by simply connecting existing sensors to the transmitter HB-WSK. ○ The bed exit sensor notifies wirelessly in conjunction with the nurse call. ○ Up to 5 transmitters can be registered with one receiver. ○ The communication distance between the transmitter and receiver is approximately 10 meters. ◎ For more details, please contact us or download the catalog.

Full and empty management refers to the real-time display of parking availability and the management of efficient use of parking spaces. By utilizing Hotron's sensors, drivers can quickly discover available parking spaces, achieving efficient parking lot operations. ■ For large parking lots, the "floor management method" and "block management method," which focus on cost reduction, are recommended. Sensors are installed at regular intervals to count the number of vehicles passing through. This method offers the advantage of easy installation and low costs. 【Target Products】 - Vehicle Count Sensor CCS2 - Ultrasonic Sensor HM-UX2/UW2 ■ For smaller scale operations, the "space management method," which installs sensors in each parking space to display availability with high accuracy, is recommended. By ensuring accurate full and empty displays, it helps prevent unnecessary entry of new vehicles and enables safe parking lot operations. 【Target Products】 - Occupancy Detection Sensor HM-UX2/UW2 - Occupancy/Pass Detection Sensor HM-LC6 - Occupancy Detection Sensor HM-LC7/LC7-FLS - Occupancy/Pass Detection Sensor HM-S6 - Occupancy Detection Sensor HM-S8

Castem Co., Ltd. will exhibit at the "Monozukuri World Osaka - Mechanical Components Technology Exhibition" held at Intex Osaka from Wednesday, October 1 to Friday, October 3, 2025. We will showcase lost-wax precision casting and MIM (Metal Injection Molding) products, as well as introduce our new technology, mold-less casting "Digital Cast." In addition to our popular casting demonstrations, we will present case studies on solving issues related to metal parts. Please utilize our "Technical Consultation Booth" to learn about optimal manufacturing methods tailored to your needs, from ultra-small lots to mass production. 【Exhibition Overview】 Dates: October 1 (Wed) - October 3 (Fri), 2025, 10:00 AM - 5:00 PM Venue: Intex Osaka (1-5-102 Nanko-Kita, Suminoe-ku, Osaka City, Osaka Prefecture) Exhibition Booth Number: Hall 6, B Hall 51-1 Pre-registration allows for smooth entry. It is convenient to register via the URL below before your visit. We sincerely look forward to your attendance. https://www.manufacturing-world.jp/osaka/ja-jp/register.html?code=1431877272389396-VEK

From November 11, 2025 (Tuesday), at Pacifico Yokohama, we will be exhibiting at interOpto2025 / Light and Laser Science and Technology Fair (organized by the Optical Industry Technology Promotion Association / Optronics Corporation) with a focus on: - UV-transmitting glass that can be molded - Diffusion glass that can uniformly diffuse incident light - A double-sided lens array that is molded without lamination 【About the Exhibition】 Event Name: interOpto2025 / Light and Laser Science and Technology Fair UV Fair Date: November 11 (Tuesday) to 13 (Thursday), 2025 Opening Hours: 10:00 AM to 5:00 PM Venue: Pacifico Yokohama Exhibition Hall C Booth Number: C-15 Organizer: Optical Industry Technology Promotion Association / Optronics Corporation Official Website: https://www.optronics.co.jp/interopto/ We invite everyone attending this exhibition to visit our booth "Gosuzumi Seiko Glass." We sincerely look forward to meeting you on-site.