ウェーブクレスト List of Products and Services

To meet the needs of smart agriculture, Milesight's "LoRaWAN Agricultural Monitoring Node-to-App Starter Kit" aims to simplify the remote monitoring process, build data-driven insights for agricultural strategies, and enable farmers to earn more money. Milesight provides a complete solution that includes several agricultural sensors. The LoRaWAN gateway covers the entire farm and can connect to hundreds of sensors. Additionally, the LoRaWAN controller uses relay outputs to control equipment such as pumps and fans.

• Other measuring instruments
• Environmental Survey

Make buildings smarter with IoT strategies! By utilizing IoT technology, we collect data from various aspects within the building through networked sensors using LoRaWAN and the IoT cloud. By using IoT devices to extract information on light, indoor air quality, lighting, PIR (motion), energy consumption, and security, we can fully operate within the building. This enables us to achieve greater efficiency, cost optimization, and reduced environmental impact for the building.

• Other measuring instruments
• Environmental Survey

<IAQ Solution Kit Contents> ● 3-in-1 IAQ Sensor AM103 / AM103L ● 9-in-1 IAQ Sensor AM319 / AM307 ● Mini LoRaWAN Gateway UG63 ● Milesight IoT Cloud

• Other measuring instruments
• Environmental Survey

The probe shows a very flat response from 30Hz to 70MHz and is characterized by a frequency range from 1Hz to 200MHz. In contrast to the RF current monitoring probes designed for EMC applications typically used for measurements in the frequency domain, the TBPCP2-3070 is used for surge or RF pulse current monitoring applications in the time domain. The aperture of the RF current monitoring probe is 25 mm. The transfer impedance measured with a 50Ω + 50Ω loop test fixture is -26 dB Ohms with a 3dB bandwidth from 30Hz to 70MHz.

• others

TBJT01 is a broadband injection transformer for measuring the stability of control loops. It provides galvanic isolation between the sweep signal source and the control loop. The injection transformer is internally terminated with a 5-ohm resistor and protected by a 100 mA fuse. The available frequency range is from 10 Hz to 45 MHz.

• others

TBJT02 is a broadband injection transformer for measuring the stability of control loops. It provides galvanic isolation between the sweep signal source and the control loop. The injection transformer is internally terminated with a 5-ohm resistor and protected by a 100 mA fuse. The available frequency range is from 1 Hz to 7 MHz.

• others

【Remote On/Off】 Remotely turn on/off electrical appliances from your mobile phone. 【Time-Based On/Off】 Create a schedule to automatically turn remote appliances on/off. 【Power Consumption Measurement】 Measuring power consumption and flexible scheduling helps save energy and reduce electricity costs. 【Overload Protection】 Overload protection prevents damage to connected appliances, safety fuses, and the smart socket itself from overcurrent. 【User-Friendly】 Switching and setting devices on/off via NFC technology from a mobile phone or PC.

• Other office supplies
• IoT
• Other measuring instruments

The WS301 LoRaWAN magnetic contact switch (door sensor) can be installed on any door or window to detect opening and closing events. By alerting you to intrusions or unauthorized access, it adds physical security monitoring to your location.

• Entrance and exit control system
• Security Sensor Systems
• Other security systems

The EM500-UDL provides high-precision distance measurement for various applications in harsh environments, such as flood monitoring, drainage management, and monitoring filling levels of grains and fertilizers. The measurements are based on ultrasonic waves transmitted from nearby objects and reflected back. ● Distance and level measurement ● LoRaWAN wireless ● Easy configuration via NFC ● 10-year battery life

• IoT
• others

The GS301 LoRaWA toilet odor detector is compact in size, making installation and maintenance easy. It is coated with moisture-resistant paint, allowing it to adapt to various conditions in bathrooms. ● Detects NH3 & H2S with higher accuracy ● Wireless deployment with a battery life of up to 3 years ● Supports LoRaWAN and Milesight D2D simultaneously ● Built-in buzzer and traffic light indicator for alarms

• IoT
• others

The GS101 is a LoRaWAN gas detector for residential use that detects methane (CH4) leaks in homes, apartments, hotels, and more, helping to avoid potential damage before danger occurs. <Detecting Hidden Dangers - Ultra-Safe Gas Alarm Threshold> The LoRaWAN gas detector is equipped with a low gas alarm threshold of 8% Lower Explosive Limit (LEL), quickly alerting residents to emergencies.

• IoT
• others

The 3D ToF people counting sensor VS132, which adopts the latest 3D ToF technology and LoRaWAN wireless deployment, is highly compatible with bidirectional line-crossing human detection applications based on its advantages of ultra-high precision of 99.5% and 100% anonymous detection, allowing for accurate and valuable statistics for further decision-making.

• IoT
• others

The UG56 is a high-performance 8-channel LoRaWAN gateway that provides reliable connectivity for industrial applications. ● Industrial-grade design ● Listen Before Talk ● Gateway fleet ● Free embedded network server ● Multiple backhaul connectivity ● Global LoRaWAN frequency plan (RU864/IN865/EU868/AU915/US915/KR920/AS923)

• IoT
• others

Industrial-grade LoRaWAN Gateway ● IP65 compliant ● NXP quad-core processor ● Semtech SX1302 LoRa chip ● Multiple backhaul connectivity ● Embedded network server ● Supports multiple network servers ● Global LoRaWAN frequency plan ● (CN470/RU864/IN865/EU868/AU915/US915/KR920/AS923)

• IoT
• others

● Eye-catching design ● Overwhelming connectivity ● Blind spot coverage ● Gateway fleet ● High compatibility - Embedded network server - LoRa basic station - Compatible with major network servers - The UG63, which has a built-in network server, supports Semtech's latest packet forwarder and is compatible with multiple network server platforms such as TTN, ChirpStack, Senet, and Orbiwise, providing a wide range of options for data processing. ● Milesight IoT Cloud - All data can be stored, managed, and analyzed with just a few clicks.

• IoT
• others

Monitoring indoor air quality (IAQ) with a compact design tailored to needs. The AM103/AM103L is compatible with industry-standard LoRaWAN gateways, allowing communication over a range of up to 2 km in urban areas and up to 15 km in rural areas.

• Other analytical equipment
• Environmental Survey
• Other measuring instruments

The AM100 series sensors perfectly integrate with Milesight IoT Cloud (Web & App), allowing you to monitor data from the office or on the go.

• Other analytical equipment
• Environmental Survey
• Other measuring instruments

Monitor ambient conditions anytime, anywhere with Milesight IoT Cloud. Achieve scene-based automation through integration with Milesight IoT sensors.

• Other analytical equipment
• Environmental Survey
• Other measuring instruments

The TH1991/TH1992 series high-precision source/measurement units can output DC voltages up to ±210V, DC currents of ±3A, and pulse currents of ±10.5A, with a minimum power and measurement resolution of 10fA/100nV. They support high-speed sampling and can generate arbitrary waveforms. Additionally, they feature a Linux operating system as the base layer, a 7-inch capacitive touchscreen with an interactive graphical user interface, and various display modes. They are equipped with diodes, triodes, MOS tubes, IGBTs, and other devices. The I/V curve scanning function allows for IV function tests to be completed without connecting to a host computer, significantly improving testing efficiency. The TH1991/TH1992 series high-precision source/measurement units offer comprehensive and integrated power and measurement capabilities, making them ideal for testing semiconductors, active/passive devices, and a variety of other devices and materials. They are widely used in R&D and educational applications, industrial development, testing, and manufacturing.

• Other measuring instruments
• Measurement and analysis equipment leasing and rental

<Super Compact Form Factor> A true handheld device specially designed for convenient outdoor use in various challenging environments. <Compatible with Various Antenna Systems> Can be used in conjunction with antennas and wireless systems from other manufacturers. <Resistive LCD Touchscreen> The resistive LCD touchscreen allows operation of the unit even while wearing gloves. The intuitive UI makes it easy to control the unit. <First-Class Sensitivity> Industry-leading receiver sensitivity across all frequency ranges allows for the detection of even the weakest signals. <PC Software> Use the free PC software to upload, save, compare, analyze, and print saved test data. <IP54 Rated> The IP54 international protection rating (IP code) ensures that the device is completely dustproof and can be used in rainy conditions. Available on all devices.

• Environmental Survey
• Other measuring instruments
• Airport facilities

-320MHz to 170GHz -Low VSWR -Multiple input types available -Low cost, short delivery time

• Other measuring instruments

-750MHz to 220GHz -Low VSWR -Multiple input types available -Low cost, short delivery time

• Other measuring instruments

-1.1GHz to 220GHz -Low VSWR -Multiple input types available -Low cost, short delivery time

• Other measuring instruments

-3.95GHz to 500GHz -Low VSWR -Multiple input types available -Low cost, short delivery time

• Other measuring instruments

-0.1GHz to 110GHz -Low VSWR -Multiple input types available -Low cost, short delivery time

• Other measuring instruments

●High power 500W (peak) ●DC short lightning protection ●Low VSWR ●Uniform gain ●Linked performance database ●6061 aluminum alloy ●5 GHz to 70 GHz double ridge broadband waveguide horn antenna ●V female connector (1.85 mm) ●EMC/EMI test antenna

• Other measuring instruments

The SD4345-C (standard) is an economical air-filled single-layer shield box suitable for building modules and terminal testing in fields such as smartphones, Wi-Fi, Bluetooth, smart grid devices, automotive electronics, drones, and smart homes. The solution platform consists of more than 12 rigorous processes, including high-quality large plate laser CNC cutting, sheet metal forming, electroplating, electrostatic spray painting, assembly and trial operation, aging, testing, and others, providing high shielding effectiveness, reliable structure, and stable performance advantages. The selection of filters can be made based on the actual needs of the customer, allowing for the configuration of appropriate I/O data interfaces and RF interfaces, or the completion of the development of non-standard communication interfaces.

• others

The SD6058 series is an economical air pressure single-layer shield box. It is suitable for building testing solution platforms for smartphones, Wi-Fi, Bluetooth, smart grid devices, automotive electronics, drones, and smart home modules and terminals. The shield box consists of more than 12 rigorous processes, including high-quality large plate laser CNC cutting, sheet metal forming, electroplating, electrostatic spray painting, assembly and trial operation, aging, testing, and others, providing high shielding effectiveness, reliable structure, and stable performance advantages. The selection of filters can be made based on the actual needs of the customer, allowing for the configuration of appropriate I/O data interfaces and RF interfaces, or the completion of the development of non-standard communication interfaces.

• others

Basic accuracy: 0.05% Auto balance bridge technology Spot measurement, list sweep, graphics sweep

• Analysis and prediction system
• others

The TBMDA-CDN25 modulated amplifier provides the power, bandwidth, and modulation necessary for conductive immunity testing using CDN and BCI probes in the frequency range of 100 kHz to 250 MHz. It is designed to be driven by a signal generator or a tracking generator of a spectrum analyzer.

• others

**Product Overview** The TBBCI1-800K420 is a Snap-On bulk current injection probe. The BCI probe is designed primarily for conducting immunity testing of automotive products in the frequency range of 1 MHz to 400 MHz, in accordance with the standard ISO11452-4. The insertion loss is 5 dB over most of the bandwidth. It complies with the insertion loss specifications of ISO11452-4 in the frequency range of 250 kHz to 230 MHz. The probe is individually characterized and can be used in the frequency range of 10 kHz to 450 MHz. This probe can be used for injections of severity I (60mA), II (100mA), III (150mA), IV (200mA), and customer-specific severity V (up to 350 mA). This probe can also be used for RF current monitoring applications. The opening of the RF current monitoring probe is 27 mm. The standard insertion loss is 5 dB, and the standard transfer impedance is 26 dB ohms.

• others

**Product Overview** The TBBCI1-200K280 is a Snap-On bulk current injection probe. The BCI probe is designed primarily for conductive immunity testing in the frequency range of 150 kHz to 230 MHz, in accordance with the standard IEC / EN 61000-4-6. The insertion loss is 8 dB over most of the bandwidth, fully complying with the insertion loss specifications of IEC / EN 61000-4-6. The probe is individually characterized and can be used in the frequency range of 10 kHz to 300 MHz. According to IEC/EN 61000-4-6, it can inject into conductive immunity test setups at severity levels 1, 2, 3, and level X, with a maximum of 30V. This probe can also be used for RF current monitoring applications. The opening of the RF current monitoring probe is 27 mm. The standard insertion loss is 8 dB, and the standard transfer impedance is 26 dB ohms.

• others

**Product Overview** The TBL5032-3 is a line impedance stabilization network that measures conducted interference in the range of 9 kHz to 30 MHz, in accordance with the CISPR 16-1-2 standard. This device is designed to test three-phase and single-phase AC power supplies with a maximum supply voltage of 450V/260V and 32A. Conducted noise can be measured on each phase and the neutral line. The TBL5032-3 features individual RF outputs for each phase and neutral, allowing it to be combined with the TBLM1 to separate emissions into common mode components and differential mode components. While the TBL5032-3 does not have an integrated high-pass filter for the RF output, it comes with an external 9 kHz coaxial high-pass filter. The single-phase DUT socket is available in country-specific variations.

• Measurement and analysis equipment leasing and rental

Compliant with the latest EMI/EMC standards.

• Other measuring instruments

● 3-in-1 field meter: spectrum analysis (DC to 10MHz), wideband (DC to 90GHz), electrostatic field measurement ● Real-time FFT-based spectrum analysis through digital processing ● Weighted peak measurement (WPM) for automatic and real-time comparison with limit values ● Auto-gain function dedicated to peak detection ● Results displayed in RMS and peak values ● Time domain measurement function for specific frequencies ● Automatic field probe recognition ● Selection of E&H fields ● Total field value and values for each component (X, Y, Z) ● Frequency span selection ● High-pass filters at 1Hz, 10Hz, 25Hz, and 100Hz ● Max hold function ● Display of maximum, minimum, and average values ● Measurement time adjustable from 1 second to 100 hours ● Programmed measurement starting at a specified time ● Graph display of wideband measurements changes over time ● Graph display adjustable from 1 second to 12 minutes ● Programmable alarm function ● Real-time digital output for external measurements ● USB-C and fiber optic connection ● Screenshot function for reporting ● PC software for control and reporting ● Multilingual support

• others

The EMC compliance software EMCview is an easy-to-use EMC pre-compliance test for radiated and conducted emissions. It fully complements automated testing using our LISN, RF current probe, measurement antennas, and TEM cells. With built-in amplitude correction, it allows for correction factors and conversion factors for cables, amplifiers, attenuators, LISNs, TEM cells, antennas, RF current probes, filters, and other components within the signal chain. No time-consuming setup is required. The software will be ready for measurements immediately after installation. All emission-related standards and several automotive manufacturer standards are pre-configured in the corresponding project files. The project files handle all the settings necessary to perform measurements in compliance with the standards. In addition to using pre-configured projects, users can easily create their own projects using the built-in editor or a simple text editor.

• Other measuring instruments

The TH2832X series features three models. Measurement frequency: 20Hz to 200kHz, high precision.

• Other measuring instruments

Built-in bias power supply of 0-100mA/0-10V, maximum test speed of 75 times per second, improved DCR testing function, basic accuracy of 0.05%.

• Other measuring instruments

The TH2638 series is a new precision capacitance meter equipped with higher test frequencies. Its compact and portable design makes it convenient for use on shelves. With a basic accuracy of ±0.07%, a loss accuracy of 0.0005, a maximum test frequency of 1MHz, a 4.3-inch LCD screen, and selectable Chinese and English operating interfaces, the TH2638 series is easy to operate and provides fast and reliable testing for the manufacturing of ceramic capacitors. It can test all types of capacitors from low to high values. The results of testing a single capacitor multiple times are very stable and accurate, even for capacitors with small values. The tester is compatible with the SCPI command set and consists of a manipulator and scanner interface, with the scanner interface capable of scanning open/short/load error calibration for each of the up to 256 channels. At low frequencies, there is a signal level correction function. When the impedance is very low, the internal resistance of the signal source and test cables can cause the voltage at the DUT terminals to be lower than the set range. This function adjusts the level to the set range.

• Other measuring instruments

The TH2689/TH2689A is a rapid and accurate capacitance leakage current insulation resistance tester. With a maximum testing speed of 18 tests per second, excellent performance, and a reasonable price, it offers the best choice for users. The TH2689/TH2689A provides a maximum test voltage of 800V/500V and a charging current of 0.5mA to 500.0mA (with a maximum power limit of 50W for voltages over 100V). It is mainly applicable for capacitance leakage current, insulation resistance, and pressure testing of aluminum electrolytic capacitor anode foils. It can also be used for checking and leakage current testing of devices such as extinguishers, Zener diodes, and neon tubes. It features a standard handler interface for achieving sorting effects and stable, rapid testing. A standard RS 232 interface, optional GPIB interface, and common RS232 software are provided to meet the requirements for connecting to a computer to form an automatic testing system. This device can receive SCPI commands to ensure compatibility with communication software.

• Other measuring instruments

This device adopts a new generation of AC/DC modulation test theory, adapting to high precision and high frequency testing requirements. The high-performance built-in embedded MCU can quickly respond to the status or malfunctions of the host and slave machines, providing real-time display. This helps improve work efficiency. The newly designed user-friendly graphical operating interface includes five foot control modes and full touch operation, offering convenience and efficiency to users. The new file management system allows for easy, quick, and accurate operation, capable of storing 99 groups of real-time setting files and user-defined setting files. It can provide push information display and cache 2 real-time information. With a two-mode SCPI command system, it is convenient for production line setup and standalone testing. It can also connect to any device with a serial port, referencing the SCPI command system design of this machine.

• others
• Other measuring instruments

The loop antenna TBMA6-P is designed for radiated emission measurements in the frequency range of 9 kHz to 30 MHz, in accordance with CISPR 16. The diameter of the loop is 60 cm, providing sufficient sensitivity to perform all relevant measurements specified in the corresponding CISPR standards for the frequency range of 9 kHz to 30 MHz. The loop is constructed from coaxial cable and is attached to the transducer with an N connector. This design allows for flexible use with various loop diameters. An attachment with a ¼-inch screw enables connection to a standard tripod.

• Other measuring instruments

【Product Overview】 The Shielded Tent TBST-86/49/45/2-B is designed to suppress interference from ambient noise during EMC pre-compliance measurements. With dimensions of 86cm x 49cm x 45cm, it is compatible with TBTC0 / 1/2 and all LISNs. The shielded tent consists of two layers of conductive fabric and is supported by a rigid aluminum profile. The side filter panel includes a 240V / 10A AC filter, two 240V / 10A DC filters, and four coaxial feed-through adapters with screw caps. The access opening is sealed with conductive Velcro tape.

• Environmental Survey

**Product Overview** The TBST-200/100/100 shielded tent is designed to suppress interference from ambient noise when performing pre-compliance EMC measurements. The dimensions of the TBST-200/100/100 are 200cm x 100cm x 100cm. The tent can accommodate Tekbox pre-compliance test equipment such as LISNs and TEM cells. The shielded tent consists of two layers of conductive fabric and is supported by a rigid aluminum profile. The side filter panel includes a 240V / 10A main AC filter, two general-purpose 240V / 10A AC/DC filters, and four coaxial feed-through adapters with screw caps. The access opening is sealed with conductive Velcro tape.

• Environmental Survey

**Product Overview** The Shielded Tent TBST-120/60/60/2-B is designed to suppress interference from ambient noise during pre-compliance EMC measurements. With dimensions of 120cm x 60cm x 60cm, it can accommodate Tekbox pre-compliance test equipment such as LISN and TEM cells. The shielded tent is made up of two layers of conductive fabric and is supported by a rigid aluminum profile. The side filter panels include a 240V / 10A AC filter, two 240V / 10A DC filters, and four coaxial feed-through adapters with screw caps. The access openings are sealed with conductive Velcro tape.

• Environmental Survey