エンベデッドテクノロジー List of Products and Services

The MPC104-ISODAC16 is a 16-bit resolution, isolated DA converter board. It has 8 channels of analog output signals. It is RoHS compliant. ◆ Features The DAC control signals are isolated using optocouplers, and an isolated DC-DC converter is used for the analog power supply, ensuring isolation between analog and digital components. The DAC interface is serial (SPI/QSPI or MICROWIRE compatible), but it has been designed for ease of use with FPGA adoption, allowing control via memory access. The analog output section uses operational amplifiers, enabling adjustment of offset and gain. ○ The 12-bit version 'MPC104-ISODAC12 ¥35,800 (excluding tax)' is also available and well-received! (For more details, please visit our website.)

• others

The output signal and input signal are isolated by a phot coupler, and the withstand voltage of the external power supply for output is a maximum of 36V. The communication protocol can be selected between I2C or SPI. The input signal is turned on/off by the current flowing through the phot coupler. ◆ Features Input Section ◎ Wide Input Voltage Range The voltage of the input signal can be specified as 5V, 12V, 24V, or 36V, which will be set at the time of shipment. Output Section ◎ High Voltage and High Output Current The output section covers a wide voltage range from 5V to 36V using FETs. The power supply is provided externally. Common Section ◎ Isolation from External Sources The internal circuit is electrically isolated from the external circuit by the phot coupler, preventing malfunctions and electrical damage caused by abnormal voltages, noise, or ground level fluctuations from outside. ◎ Board Size Same size as Raspberry Pi 3 MODEL-B and Raspberry Pi 2 MODEL-B. ◎ Connection with Raspberry Pi Connect to the 40-pin (GPIO) of the Raspberry Pi and communicate via I2C or SPI. ◎ When connecting to the 40-pin connector of the Raspberry Pi, an MPC-RASST may be required as an intermediary board.

• others

The RAS64DIO is an expansion I/O board developed for the Raspberry Pi. The input and output signals are bidirectional buses, and can be set to input or output on a per-port basis via commands, totaling 64 bits for input and output. It is RoHS compliant. ◆ Features Input Section ◎ Input voltage range: 3.3V to 5V, CMOS logic signals All input signals can be selected as +5V pull-up or GND pull-down. (All ports are pull-up by default) Output Section ◎ Equipped with SN74HC574PWR Outputs a voltage of 5V and a current of 20mA (short circuit). Common Section ◎ Board size Same size as Raspberry Pi 3 MODEL-B and Raspberry Pi 2 MODEL-B ◎ Connection with Raspberry Pi Connects to the Raspberry Pi's expansion connector and communicates via I2C or SPI. ◎ When connecting to the Raspberry Pi's expansion connector, an intermediate board such as MPC-RASST may be required.

• others

The MPC-RAS-ST is an expansion board that converts the Raspberry Pi's UART signals to RS232C driver receiver. Optionally, an isolated DC-DC converter with 5V output and 9V to 36V input can be added. By stacking it on top of the Raspberry Pi, it further connects the BUS signals to an upper level. It is RoHS compliant. ◆ Features - Converts the Raspberry Pi's UART signals to RS232C levels. - Allows for the installation of additional expansion boards on the upper level via a vertical connection connector on the Raspberry Pi's bus connector. - Enables power input of 9V to 36V through the addition of power options. ◎ Board Size Same size as Raspberry Pi 3 MODEL-B and Raspberry Pi 2 MODEL-B ◎ Connection with Raspberry Pi Connects to the Raspberry Pi's GPIO 40-pin expansion connector.

• others

The I9603-IF-01 is an interface board developed with technical cooperation from the Japan Agency for Marine-Earth Science and Technology (JAMSTEC) specifically for the Iridium satellite communication terminal SBD9603N. It supports dual power input of DC 6V to 32V or DC 5V, allowing the signals from the SBD9603N to be connected to external devices via connectors. It is ideal for use in locations where communication infrastructure is lacking, such as in space or at sea. ◆ Features ◎ Wide input voltage range of 6V to 32V and direct supply of 5V power (5V power takes priority when both power sources are supplied simultaneously) ◎ Compact size of 60mm x 45mm ◎ External power ON/OFF control is possible ◎ Converts the RF connector (u.FL) of the SBD9603N to an SMA connector ◎ Allows external access to the SBD9603N serial signals via connectors (supports 3-wire and D-Sub9) ◎ Implements overvoltage protection circuit for 5V input above 5.6V ◎ Communication signals with the SBD9603N can be selected as either 3.3V logic signals or RS232C signals * The 'MPCIRI-2014' with built-in control functions is also available for sale! For more details, please visit our website.

• others

The "MPC104-ISOADC16-P-V1" is a 16-bit isolated AD converter board for the PC104 bus, while the "MPC104-ISOADC16-U-V1" features a USB interface. It has 8 channels of AD input signals and also includes isolated input/output ports (8-bit input / 8-bit output). This is a successor to the MPC104-ISOADC16 and is backward compatible with the MPC104-ISOADC16-x-V1. It is RoHS compliant. The 12-bit version "MPC104-ISOADC12 ¥27,800 (excluding tax)" is also available and well-received! (For more details, please visit our website.)

• others