Last Updated： Aggregation Period:Sep 24, 2025～Oct 21, 2025
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:Sep 24, 2025～Oct 21, 2025
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:Sep 24, 2025～Oct 21, 2025
This ranking is based on the number of page views on our site.
106～120 item / All 243 items
It is a small type of circuit protector that can be mounted on a flange.
Manufacturer: Sang Mao Co., Ltd. Headquarters Factory: Taiwan Certifications Obtained: UL CSA VDE The A-0702F series allows for connection assembly in small spaces with a width dimension of 8.5mm. It is possible to supply user-specified rated currents ranging from 1 to 20A.
Protect your equipment from high voltage surges such as induced lightning that enter the power line! Surge protector for power supply (AC100V) SP001P-AC110!
High voltage surges caused by induced lightning, such as those from lightning strikes, can damage video equipment like cameras and DVRs. A surge protector is designed to block these high voltage surges, including induced lightning, that travel through this cable and protect the equipment. It is installed at both ends of the cable used for transmission. The SP001P-AC110 is a surge protector for AC 100V equipment such as surveillance cameras. The power connection is via a terminal block.
AC/DC power surge protector SP001P protects equipment from high voltage surges such as induced lightning that can enter power wiring!
High voltage surges caused by induced lightning, such as from lightning strikes, can damage video equipment like cameras and DVRs. The surge protector is designed to block induced lightning that travels through this cable and protect the equipment. The SP001P is a surge protector for AC/DC power supplies. It allows currents of up to AC 40V and DC 56V to pass through. The power connection is made via a terminal block.
Surge protector SP001VPD protects devices from induced lightning transmitted through the wiring of surveillance cameras (video, power, control signals)!
Lightning strikes can cause induced lightning to occur, which may damage video equipment such as surveillance cameras and DVRs. The surge protector is designed to block the induced lightning that travels through this cable and protect the equipment. It is used by attaching it to both ends of a long transmission cable used for transmission. The SP001VPD is a device that adds protection for signal lines (RS485, sensors, etc.) to the SP001VP (for video and power). It simultaneously protects video (AHD/HD-TVI/HDCVI/composite compatible), power, and signal lines. The connections for the signal lines and power lines are made via terminal blocks. - Control signals such as RS485 and contact signals (2-wire type) are protected. - The camera power can be used with a maximum of AC40V and DC56V (allowing power below AC40V and DC56V to pass through).
Surge protector SP007 compatible with SD/HD/3G-SDI video signals transmitted via coaxial cable!
- It blocks surges that occur in SD/HD/3G-SDI video signals (BNC connection). - It protects equipment from sudden voltage spikes caused by high-voltage surges such as induced lightning. - It can also be used for analog cameras and TV/CATV antenna cables. - With BNC male on one end and BNC female on the other, it can be easily installed on existing wiring. - It allows voltages below DC24V to pass through.
PoE-compatible Ethernet 16-channel surge protector SP016P that protects devices from high voltage surges such as induced lightning in LAN wiring!
The SP016P simultaneously protects LAN wiring that includes PoE/PoE Plus power supply for up to 16 systems at 10/100/1000M. It diverts high voltage surges caused by induced lightning and other sources away from the equipment to the ground before it reaches the devices. The surge protector should be installed as close as possible to the equipment that needs protection. When protecting a camera, it should be placed near the camera; when protecting a monitor or NVR/server, it should be installed near the monitor/DVR/server. The basic principle of surge protection is to install protectors on both the camera side and the display device (monitor) side. If the SP016P is installed on the monitor side, additional devices such as the IP06PH or JPOE-B2-1, SP006P can be installed on the camera side for each camera wiring system.
Surge protector for DC power/signal to protect equipment without grounding work MLT4-B1-1-12!
MLT4-B1-1-12 is a surge protector compatible with power supplies and control signals up to DC12V, including contact signals. - No grounding work is required to protect devices from various surges. It blocks surges from power wiring and surges caused by electromagnetic pulses. It is also effective against surges caused by chattering and the OFF state of inductive load circuits, which cannot be eliminated by conventional lightning arresters.
HDMI surge protector SP008 that protects video equipment from surges transmitted through HDMI cables!
Protects video equipment from surges transmitted through HDMI cables. - Protects devices from sudden voltage spikes caused by induced lightning, ESD, and EFT (impulse noise). - Compatible with HDMI 1.4. - Response time is less than 1 ns. *Be sure to attach a ground cable to the main unit for grounding (Type D grounding).
SP009 protects video equipment from high voltage surges transmitted through AHD/HD-TVI/HDCVI and composite video signal transmission cables!
The SP009 is a surge protector that protects video equipment from high voltage surges transmitted through AHD/HD-TVI/HDCVI and composite video signal transmission cables. - It protects connected equipment from rapid voltage increases caused by induced lightning and other sources. - The terminals are BNC male to BNC female, allowing for direct connection between the BNC terminal on the back of the camera and the cable. * Please connect the equipment to be protected at the Equipment End of the cable that may have surges flowing in at the Cable End. * Ensure that the ground wire is properly grounded (Type D grounding).
16-channel surge protector SP016HD compatible with AHD/HD-TVI/HDCVI/composite video (rack mountable)!
The SP016HD is a surge protector for 16 channels that supports AHD/HD-TVI/HDCVI composite video transmitted via coaxial cable (BNC connector). It is a 1U size that can be mounted in a 19-inch rack and allows for the connection of up to 16 video channels. It diverts surges caused by induced lightning and other sources in the transmission cable to ground before reaching the equipment. The surge protector should be installed as close as possible to the equipment that needs protection. When protecting a camera, it should be placed near the camera, and when protecting a monitor or DVR, it should be installed near the monitor/DVR. The basic surge protection strategy is to install protectors on both the camera side and the display device (monitor) side. If the SP016HD is installed on the monitor side, additional SP009 (for one channel) units can be installed on the camera side for each camera wiring.
Protect important equipment from induced lightning, noise, and other surges without grounding work! Coaxial cable SPD that firmly guards surveillance cameras and video transmitters!
- Coaxial cable surge protector JMSB-HDV-P with SEAT method (absorbing surge energy and dispersing it) that does not require grounding - Surge protector suitable for coaxial cable wiring of video signals/high-frequency signals - Usable with HD-SDI/AHD/HD-TVI/HDCVI/analog video signals - Compatible with power-over devices (passing voltage: up to DC76V) - Protects both signal lines and power lines - Protects equipment from various surges without the need for grounding work - Blocks surges caused by electromagnetic pulses - Blocks surges caused by switching and lightning transients * Please connect transmission cables that may have surge contamination to the "IN" side and the equipment to be protected to the "OUT" side.
Outdoor surge protector SD-201 compatible with PoE++ (95W) powered Ethernet LAN cables!
The SD-201 is a surge protector for LAN cables that supports communication speeds of 10M/100M/1G/2.5Gbps and PoE++ (95W) power supply over Ethernet, protecting connected devices from induced lightning of up to 20kV that may occur on LAN cables. *It is IP67 rated and can be installed outdoors.
SP009T protects video equipment from high voltage surges transmitted through UTP cables carrying AHD/HD-TVI/HDCVI and composite video signals.
The SP009T is a surge protector that protects video equipment from high voltage surges transmitted through AHD/HD-TVI/HDCVI and composite video signal transmission cables (twisted pair transmission). - Protects equipment from sudden voltage spikes caused by induced lightning and other sources. - Connection terminals are terminal block to terminal block. - Can also be used with control signals such as RS485. * Please connect the equipment to be protected at the Equipment End of the cable, where there is a possibility of surges entering at the Cable End. * Ensure that the ground wire is properly grounded (Type D grounding).
Surge protector that protects video equipment from high voltage surges, such as induced lightning, transmitted through analog HD and composite video signal cables!
The SP009P is a surge protector that protects video equipment from high voltage surges, such as induced lightning, transmitted through AHD/HD-TVI/HDCVI and composite video signal cables. It supports the function of transmitting power over coaxial cables (PoC) and can be used to protect cameras with power overlay and PoE coaxial transmission devices.
Build a transportable system! A highly durable and very lightweight aluminum rack case.
The "Mitra Set Classic ZRGS Series" is a high-sensitivity, precision rack case for transporting electronic equipment that meets military specifications. It is made from high-strength aluminum plates and frames, offering high durability while being very lightweight. The structure is designed to withstand harsh conditions such as heat, humidity, lightning, and severe weather. Additionally, it features a shock mount mechanism that mitigates impact and vibration. It is well-suited for the transportation and outdoor use of precision equipment in fields such as defense, communications, electronics, and transportation infrastructure. 【Features】 ■ Aluminum rack case that can build a transportable system ■ Capable of accommodating EIA standard 19-inch equipment ■ Waterproof and dustproof specifications compliant with IP65 ■ Compliant with the Air Transport Association standard ATA300 Category 1 ■ EMI shielding measures available in special specifications *For more details, please refer to the PDF materials or feel free to contact us.
