Research and development of secondary batteries and all-solid-state batteries: Efficient evaluation of electrolytes using a heating furnace. Uniformly heat multiple solid electrolyte materials for screening and impedance evaluation based on temperature characteristics, allowing for accurate assessments in a short time with various heating patterns!

Minimize work inside the glove box ◎ Solid electrolyte material screening / Impedance evaluation by temperature characteristics ◎ Multiple uniform, short time, and accurate test evaluation

It excels in material screening of solid electrolytes and impedance evaluation according to temperature characteristics! ▼Features▼ 1. Reproduces various heating patterns of inorganic electrolyte heating and sintering processes in a short time - Temperature can be adjusted with an accuracy of ±1°C within a temperature range of 50°C to 1200°C - The heating rate can reach a maximum of 300°C/min, allowing for various heating patterns to be tested in a short time from room temperature 2. Efficient simultaneous evaluation of impedance measurements for lithium-ion conductivity (conductivity) - Structure allows for heating with electrodes attached to both ends of the coin cell - Coin cell holder is prepared for 4 slots - Uniform heating/measuring of 4 samples simultaneously under the same conditions - Various coin cell diameters available from Φ20 to Φ8mm 3. Simple operation and design that prevents exposure to the atmosphere / atmosphere control - Work inside the glove box is limited to sample set only - Inside the quartz tube, a quartz coin cell holder is held, and only the coin cell is accurately heated - Light heating from outside heats the completely sealed transparent quartz tube - Gas introduction system and atmosphere control during heating are also easy For more details, please contact us.

• Batteries and Capacitors
• Fuel Cells
• Other Hydrogen/Fuel Cells

Tests can be conducted while observing the condition of the material surface [using a dual-swing crosshead], keeping the sample position centered to avoid missing any changes!

The "CATY-T3H SYSTEM" is a tabletop high-temperature tensile observation device that allows for thermal fatigue testing while observing the condition of the sample surface in real-time. It can be operated easily and supports high-temperature and high-speed heating. The adoption of a dual-swing crosshead ensures that the sample's position remains centered, even with expansion and contraction, minimizing any displacement of the observation point. By combining it with optional units, it can also accommodate tests such as bending observation. 【Features】 ■ Capable of high-temperature and high-speed heating up to 1500°C * However, this depends on the shape and thermal capacity of the sample. ■ Suitable for testing not only metallic materials but also composite materials of surface-mounted components ■ Enables stress measurement, low-cycle fatigue testing, and creep testing in gas flow or vacuum conditions ■ Realizes combined testing of thermal fatigue under stress and real-time observation * For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Steel

Utilizing the know-how of custom testing machines, we support testing and research with material testing machines such as impact, fatigue durability, tensile, and torsion testing machines.

▼Examples of Testing Machine Manufacturing▼ The description is just one example. For details, please check individual pages or feel free to contact us. Customization is also available. *Special order testing machines and high-temperature in-situ observation furnaces are featured on separate pages. 1. Impact Testing Machines - Charpy (pendulum/instrumented/semi-automatic/manual/automatic specimen replenishment) for metals, non-metals, and resins. - Drop weight impact (drop/falling weight/instrumented) for metals, non-metals, resins, carbon fibers, textiles, and automotive-related materials. 2. Fatigue Endurance Testing Machines - Creep (servo-electronic/weight type/multi-station/with constant temperature bath) for metals, ceramics, carbon fibers, resins, and electric wires. - Pulley fatigue for metals and products. - Torsional fatigue for metals and resins. - Friction and wear (thrust/reciprocating/sliding/rotational) for metals, ceramics, carbon fibers, and resins. 3. Other Material Testing Machines - Universal testing machines (tensile/compression/bending) for metals, ceramics, carbon fibers, resins, and electric wires. - Static torsion testing machines for resins, rubber, etc. ▼Material Testing Machines at Yoekura▼ Since our establishment in 1980, we have been manufacturing testing machines. We consistently handle the design, development, manufacturing, maintenance, inspection, and repair of equipment, and with our accumulated know-how and technology, we have produced testing machines for various customers across different industries.

• Printed Plywood
• Ready-mix concrete
• Other measuring instruments

Fuel, engine, wheels, suspension, spark plugs, etc. Leave the creation of original testing machines and software to us! Please let us know your testing requirements!

Our company has a proven track record of creating testing machines related to the following. If you have any requests regarding other testing machines, please feel free to contact us. [ Fuel-related ] Injector durability device for poor fuel Fuel pump high-temperature durability testing device Fuel pump durability testing device Fuel pump flow measurement device Fuel pump and SIFS performance measurement device Direct injection Malvern bench [ Engine-related ] Valve seat cold heat testing machine Valve guide sliding testing machine Exhaust system fastening part cold heat fatigue testing machine Durability testing machine related Mud water durability testing machine Boots durability testing machine CVJ durability testing machine Propeller boots durability testing machine Rack boots high and low temperature durability testing machine [ Wheel and suspension-related ] Wheel rotation bending testing machine (VIA specification) Wheel drop impact testing machine (JIS/ISO) Drum durability testing machine Front fork friction testing machine Wheel lateral destruction measurement testing machine Testing machine for suspension and steering [ Spark plug-related ] SP heating load life testing machine SP dielectric strength testing machine Please contact us for other achievements.

• others

We have newly added the "RB Catcher," a log capture device installed on impermeable sediment control dams in flow sections, to our product lineup and have started sales. The RB Catcher is directly attached to the upstream part of the impermeable sediment control dam to enhance log capture functionality. Unlike the conventional straight arrangement, it features a structural layout that creates gaps between units, ensuring that water flow is maintained without causing blockages after capturing logs. This allows for the reliable capture of subsequent logs without overflow, preventing damage downstream. By adding this new log capture device to our lineup, we will flexibly respond to various needs in the field.

This time, the ACS-5000 is available as a facial recognition terminal compatible with FaceMe Security's add-on feature "Face Terminal," enabling access control management that combines "advanced anti-spoofing features" with high-speed facial recognition powered by edge AI. ■ Main Features 1. Accelerated Authentication Processing FaceMe Security is optimized for the MediaTek Genio 700's NPU, achieving faster facial recognition processing and reduced CPU load compared to processing with only the CPU. It ensures stable authentication without delays even during peak times, such as clocking in and out, contributing to alleviating congestion. 2. Advanced "Anti-Spoofing" Optimized for the IR + RGB camera mounted on the ACS-5000. It can quickly detect fraudulent authentication using photos, videos, or 3D masks within 0.6 seconds, ensuring reliable identity verification. 3. Door Control Without Additional Equipment FaceMe Security can directly control the digital I/O of the ACS-5000, allowing for the construction of an access control management system without the need for additional equipment. This simplifies system configuration and reduces implementation costs.

Do you have any concerns or requests regarding wired bed exit sensors? × Tangling or tripping over wired cables × Cable disconnection or damage × Worrying about forgetting to turn the switch back on after temporarily stopping the sensor. × Wanting to be notified of bed exits even from a location far from the nurse call outlet. Such concerns can be resolved simply by connecting our wireless nurse call linked set to the sensor! Our wireless nurse call linked set allows you to connect bed exit sensors like "Ugo-kun," "Foldable Thin Matta-kun," "Ayumi-chan," and "Just Place Pole-kun" to transmitters and receivers, reducing wiring around the bed area, alleviating concerns about tripping or falling due to cables, and contributing to a tidier work environment. Furthermore, it enables the use of bed exit sensors even from locations far from the nurse call outlet, allowing for more flexible equipment placement.

The non-contact beam touch sensor "HA-T401/HA-T520" has a compact detection range, making it an ideal automatic door sensor for installation on automatic doors facing narrow corridors or busy streets. Depending on the application and installation location, you can choose between "non-vision mounting type" and "non-vision built-in type." 【Features】 ● With the beam touch sensor, you can open and close the automatic door simply by bringing your hand close without touching it, ensuring hygiene. ● Depending on the installation environment, such as single sliding or bi-parting doors, the detection range can be set in four configurations: left, center, right, and a total of 12 spots. ● Two types of activation row settings are available to reduce unnecessary opening and closing of the automatic door due to cross traffic, contributing to energy-saving effects. ● The touch switch and infrared sensor are integrated, allowing for a switch between beam touch and infrared sensor with a single model. 【Recommended for such locations!】 ☑ Entrance facing a busy corridor ☑ Counter or sign near the door ☑ Buildings facing narrow corridors ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors ◎ For more details, please download the materials or contact us.

The receiver section of the radio is designed to receive signals properly even when influenced by other radios used in the world, and standards have been established for this purpose, requiring designs that comply with these standards. This time, I will briefly discuss the wireless standards for the receiver section! 【Contents】 ■ Minimum reception sensitivity ■ Adjacent channel selectivity ■ Receiver intermodulation ■ Spurious response ■ Harmonic emission * For more details, please refer to the PDF document or feel free to contact us.