Seismic reinforcement method for columns using slits in post-construction sections - 'Thin Residual Type Complete Slit' by high-precision machines.

Acquisition of technical evaluation from the Japan Architectural Disaster Prevention Association! Introducing a seismic reinforcement method for columns using partial slits.

The "Non-Pick Method" is a seismic reinforcement method for columns using partial slits. Construction can be carried out while residents are living in the building, providing seismic reinforcement effects equivalent to complete slits. With our specially developed cutting machine (with a special bit), continuous and consistent construction from end hole drilling to groove cutting can be achieved in one setup. Additionally, it requires no chipping, has low vibration and low noise, and produces minimal waste with excellent precision. 【Features】 ■ Continuous and consistent cutting can be performed in one setup with the dedicated cutting machine ■ The accuracy and finish of the slits are outstanding ■ No chipping required, low vibration, low noise, and dust-free construction ■ Drilling and cutting debris is in a slurry form (liquid mixed with sand particles), making disposal easy ■ The construction efficiency for cutting is approximately 3 to 5 meters per day per machine for a width of 30mm and depth of 100mm *For more details, please refer to the PDF materials or feel free to contact us.

• Reinforcement and repair materials

[Construction Photo Collection Giveaway] Equivalent seismic reinforcement effect to complete slits! Introducing construction examples in condominiums.

The "Non-Pick Method" is a post-construction slitting process that allows for continuous and consistent construction from end drilling to groove cutting with a dedicated cutting machine (equipped with a special bit) in a single setup. It is a groundbreaking method that requires no chipping, produces low vibration and low noise, and generates minimal waste with excellent precision. This photo collection of the construction showcases examples of the "Non-Pick Method" used in a certain apartment building in Tokyo. It can be utilized as a partial slitting method that allows construction to be carried out while residents are living in the building, achieving seismic effects equivalent to those of complete slitting. We encourage you to take a look at this opportunity. 【Main Features】 ■ Continuous and consistent cutting can be achieved with a single setup of the dedicated cutting machine ■ The precision and finish of the slits are outstanding ■ Dust-free construction with low vibration and low noise, requiring no chipping ■ Drilling and cutting debris is in a slurry form (liquid mixed with sand particles), making disposal easy For more details, please contact us or download the catalog.

• Reinforcement and repair materials

Obtained technical evaluation from the Japan Building Disaster Prevention Association! Earthquake-resistant reinforcement is possible while living in the home!

The "Non-Pick Method" makes previously impossible construction feasible. The "Non-Pick Method" allows for one-sided construction (partial slitting) from the exterior wall, eliminating the need to move residents, desks, chairs, equipment, and supplies, enabling construction while the building is in use! Additionally, it has obtained technical evaluation and patents from the Japan Building Disaster Prevention Association for its post-construction seismic slitting method, which has the same seismic reinforcement effect as complete slitting. 【Features】 ■ Seismic reinforcement method that does not require moving - Construction can be carried out while using the building without moving people or items! ■ High-quality slits - The finish quality and smoothness of the perforation cutting is outstanding - Fire resistance performance confirmed for 2 hours (performance test report available) ■ Significant improvement in construction environment! - Low noise, low vibration - Almost no dust dispersion (does not pollute the air around the work area) *For more details, please download the catalog or contact us.

• Reinforcement and repair materials

The "HM-S6" is an embedded park sensor that detects vehicles through changes in magnetic flux and responds to various situations from passing to stationary vehicles. It can be used for the opening and closing of input doors at waste treatment plants, as well as for gates that vehicles pass through and outdoor parking applications. It can also be installed on rebar and steel plates. 【Features】 ■ Resistant to the effects of natural environments such as rain, snow, temperature changes, and geomagnetism ■ Protection rating IP68 reduces the risk of water ingress ■ Ten times the load capacity compared to conventional embedded park sensors (based on our comparison) ■ Can distinguish between vehicles even when they pass continuously ■ Can be installed on rebar and steel plates *For more details, please refer to the PDF document or feel free to contact us.

To customers considering the introduction of vehicle detection sensors for parking lot construction, design, or management: Are you facing any challenges with current issues or selecting the right sensors for parking management? Hotron offers free materials that explain how to utilize vehicle detection sensors and the benefits of their introduction! ▽ Here is the lineup of materials ◉ Vehicle Detection Sensor Basic Guide This guide focuses on the challenges and solutions in parking lot operations, introducing the overview of vehicle detection sensors. ◉ Key Points for Introducing Vehicle Detection Sensors This material discusses the benefits of introduction based on installation locations and specific challenges. ◉ Case Studies of Vehicle Detection Sensor Implementation This document presents the challenges before implementation and the results after introduction. For more details, please download from our website and check it out. https://www.hotron.co.jp/download/

Starting from October 2025, Panasonic's indoor units for office and store air conditioners will be renewed! In this renewal, all models will come standard with "100 times nanoe X." This not only enhances comfort with commercial air conditioning but also contributes to improving air quality. Additionally, improvements in installation efficiency to enhance on-site work productivity and a strengthened lineup to accommodate diverse spaces have been implemented. The new indoor units are equipped with high concentrations of nanoe X as standard! They demonstrate a high effectiveness in purifying indoor air during air conditioner operation, providing a safer and more comfortable environment for office and store users and employees. Furthermore, the center of the suction inlet and the center of the hanging bolt have been unified. This allows for the combined use of canvas ducts and panels, improving installation efficiency. If you have any questions or would like a quote, please feel free to contact us. We will fully support you in replacing your commercial air conditioning!

We will be exhibiting at the "Advanced Construction, Disaster Prevention, and Mitigation Technology Fair in Kumamoto 2025," which will be held for two days starting from November 19 at Gran Messe Kumamoto (Masaki Town, Kamimashiki District, Kumamoto Prefecture). This exhibition is organized by the organizing committee of the Advanced Construction, Disaster Prevention, and Mitigation Technology Fair in Kumamoto 2025, aiming to enhance disaster prevention awareness through the introduction of advanced technologies and products related to disaster prevention, as well as to promote economic and technological exchanges. On the day of the event, we will showcase our "High Water Content Soil Improvement Agent MT Series" and "Soil Recycling Technology Bontelan Method," and we will introduce our technologies through practical demonstrations using actual soil. We invite those nearby to stop by our booth. Venue: Gran Messe Kumamoto (1010 Fukutomi, Masaki Town, Kamimashiki District, Kumamoto Prefecture, 861-2235) Date and Time: November 19 (Wednesday) 10:00 AM - 5:00 PM November 20 (Thursday) 9:30 AM - 3:30 PM Our Booth Location: B10 Presentation: November 20 (Thursday) 10:45 AM - 11:15 AM, Seminar Room 4 Advanced Construction, Disaster Prevention, and Mitigation Technology Fair in Kumamoto 2025 HP https://www.s-kumamoto.jp/

Kort Valuta Inc. (Head Office: Shibuya, Tokyo; CEO: Hideki Shibata) is pleased to announce that we will hold our next recruitment event, “Kort Valuta Night,” on November 26, 2025. This recurring event offers an opportunity for potential candidates to casually learn about our company culture and team atmosphere before applying. By lowering the barrier to entry and providing authentic insights from current employees, the event helps participants gain a more concrete sense of what it’s like to work at Kort Valuta. Since the event’s launch, approximately ten attendees have gone on to join the company in a range of roles — including marketing, customer support, and backend engineering.