Product condition and underfloor environment of the Dry Pro type-C after approximately 2.5 years of use.

Contributes to the suppression of condensation and mold under the floor. A new model compatible with the foundation packing method has been introduced.

The "DRY PRO" Ver3 is an electronic dehumidifying and ventilation unit for underfloor use, combining a Peltier cooling device with a dedicated stirring and diffusion-type blower. In addition to the diffusion-type model "TYPE-D" for foundation insulation methods, a new model "TYPE-C" compatible with foundation packing methods has been added to the lineup. It can dehumidify even in areas where moisture tends to accumulate by stirring a wide range of air. It helps suppress moisture and condensation under the floor, contributing to the prevention of mold, pests, and decay fungi in wooden components. Furthermore, with the version upgrade in June 2024, a powerful dehumidification operation mode has been added. The surrounding temperature range for dehumidification operation (low-temperature dehumidification operation range) has been expanded, now accommodating surrounding temperatures down to 5°C. 【Features】 ■ Easy installation with a φ22 drainage hole (no drainage pump required) ■ Automatic operation possible with a dedicated indoor controller ■ The direction of the aluminum duct of the blower can be set freely ■ Dehumidification capacity of 1800mL per day (depending on conditions) ■ Uses non-fluorinated electronic cooling technology ■ Compatible with underfloor flooding sensors (optional) *For more details, please refer to the PDF document or feel free to contact us.

• Heating and cooling equipment and facilities

Measures against condensation in summer! Condensation and corrosion within wall structures are often difficult to detect.

In 2020, the "mandatory energy-saving standards for housing" are scheduled to be implemented, and it is expected that Japanese housing will increasingly aim for high airtightness and high insulation. However, at the same time, measures against condensation during the summer must be considered. In a site where glass wool was filled using the 2x4 construction method and a vapor barrier was installed on the interior side, significant corrosion due to condensation occurred. It is believed that the interior became hot and humid, leading to condensation as it was cooled by the air conditioner on the inside. The hold-down hardware also showed white mold, and if corrosion progresses like this, it will pose problems for the durability of the building. This type of summer condensation particularly occurs in regions with high temperatures and humidity, like Japan. Therefore, it is necessary to implement sufficient measures against winter-type condensation while simultaneously preventing summer-type condensation. *For more details, please refer to the PDF document or feel free to contact us.

• Housing structure technology/long-term superior housing technology
• Heat insulation and heat shielding methods

[Demo available] Powerful airflow spreads dehumidified air over a wide area! By making a Φ22 hole for the drain pipe, installation can be easily done.

The "Dry Pro" electronic dehumidifying and blowing unit for underfloor use combines a Peltier cooling device with a diffusion-type blower to dehumidify the entire underfloor area, suppressing the occurrence of moisture and condensation! This system is designed to dehumidify the space between the foundation and the floor, suitable for housing construction methods that lack ventilation openings. On days with high humidity during the rainy season or summer: ● Powerful dehumidification at 1800ml/day It effectively resolves moisture and condensation issues, and is useful for preventing mold, pests, and decay fungi in the wooden parts under the floor. 【Features】 ■ Easy installation by simply drilling a Φ22 hole for drainage! ■ Dehumidified air is circulated widely by the blower ■ Equipped with fitonchid, which has deodorizing effects, as standard ■ Patent and design applications submitted ■ Fully automatic operation with a dedicated controller *Please note that [demo visits] may not be available in certain regions. Thank you for your understanding in advance. *For more details, please refer to the PDF materials or feel free to contact us.

• Floor and equipment composite system
• others

The cause is a large amount of water vapor! The challenge is how to remove humidity and suppress mold and decay.

Foundation insulation is a method of insulating the foundation that faces the outside air. The period when the risk of condensation and mold is highest with foundation insulation is from June to September of the first year after completion. The main cause is the large amount of water vapor coming from the concrete floor. Especially, wood that contains a lot of moisture significantly deteriorates in strength, so it is important to be cautious considering durability against earthquakes and typhoons. As a solution to these humidity problems, our company has developed a dedicated underfloor dehumidifier called "Dry Pro." It effectively eliminates humidity and condensation, and is useful for preventing mold, pests, and decay fungi in the underfloor wooden components. (Patent and design application pending) 【Features of Dry Pro】 ■ Dehumidification capacity of approximately 400-600cc per day on humid days during the rainy season and summer ■ Circulates dehumidified air widely using a blower ■ Quiet design: 45/44dB ■ Standard equipped with phytoncide that has deodorizing effects *For more details, please refer to the PDF materials or feel free to contact us.

• Safety Supplies
• Insulation work
• Heat insulation and heat shielding methods

After about one month, a drier condition (wood moisture content 12%) was confirmed!

"Dry Pro" is a floor underfloor dehumidifying fan that effectively eliminates moisture and condensation, and is effective against mold, pests, and decay fungi in the wooden parts under the floor. Assuming the early stages of new construction using foundation insulation methods, 36 liters of water were sprayed on the underfloor foundation of each building, and dried wood (cedar) was installed to measure the moisture content of the wood and the humidity under the floor. As a result, the buildings where this product was installed gradually dried out by repeatedly operating the dehumidification process every day, and after about two months, an average of approximately 70% RH dry condition was confirmed even outside of dehumidification operation hours. [Experiment] ■ Test House A - Floor area approximately 10 tsubo - Underfloor with foundation insulation method (Dry Pro installed) ■ Test House B - Floor area approximately 10 tsubo - Underfloor with foundation insulation method (without dehumidifying fan) *For more details, please refer to the PDF document or feel free to contact us.

• Insulation work
• Air compressors, blowers and pumps
• Heat insulation and heat shielding methods

PERI products are used at construction sites around the world. This time, we would like to introduce the construction work of the "Dunajec Road Bridge" spanning the Dunajec River in the town of Nowy Targ in southern Poland. The road bridge was planned to be constructed using a balanced cantilever method, dividing the cantilever beams starting from each pier into 10 segments. A particular concern was to strictly adhere to the concrete pouring cycle for each segment. To achieve this, a balanced cantilever carriage (VBC) equipped with a hydraulic advance system and an automatic formwork stripping function was adopted. By utilizing the VBC, it became possible to pour concrete for segments up to a maximum length of 5 meters in a single cycle, allowing for efficient and timely construction. PERI products: 1. TRIO Panel Formwork 2. VARIO GT24 Wall Formwork 3. PERI UP Flex Modular Scaffold 4. VST Heavy-Duty Shoring Tower PERI Japan Co., Ltd.

At a major purchasing specialty store located in Kanagawa Prefecture, we have introduced our commercial aroma diffuser rental service "MajestaFragrance," enhancing the store's atmosphere with fragrance. Installed models: MFmini (4,400 yen per month) × 2 units Adopted fragrance: Freesia Pear To ensure that customers visiting the store can relax during their appraisal and consultation time, we have implemented space branding with a "refined and approachable scent." The fragrance used is "Freesia Pear," which pleasantly spreads the freshness of fruity pear and the vibrant aroma of freesia. It warmly welcomes customers with a clean and high-quality scent. The "MFmini" introduced this time is a compact yet powerful diffuser known for its strong diffusion capabilities. It blends smartly into limited installation spaces such as reception counters and customer service areas, efficiently delivering fragrance. At Majesta Fragrance, we offer optimal diffuser models and fragrance suggestions tailored to the size of the store, type of business, and interior atmosphere. A "free trial installation" is also available before signing a contract.

Hotron Inc. has launched its new product, the "Vehicle Count Sensor CCS3"! This product is a ceiling-mounted sensor that combines infrared and radar technology. It reliably detects vehicles in both directions with a single unit, accommodating traffic during congestion and vehicle passing, thus achieving efficient occupancy management in large parking lots. Additionally, it can be utilized for exit warning purposes in addition to vehicle counting, contributing to the safe and smooth operation of parking facilities. 'Features' - Improved detection performance against changes in road surface during rainy weather by using both infrared and radar. - Equipped with IP67 waterproof and dustproof performance, making it effective even in salt damage areas. - Various settings can be configured from a dedicated app (for Android devices), with current settings easily visible at a glance. - The base dimensions are the same as the previous model "CCS2," allowing for smooth replacement of existing equipment. *For more details, please refer to the product information, catalog download, or contact us.*

We will be exhibiting at the "Osaka Industry Exhibition 2026" held at MyDome Osaka from October 14 (Wednesday) to 15 (Thursday), 2026. We will introduce our stress check, health management system, reservation and reception system, and interview system.

We have published the latest issue (Issue 94) of the ISO-related information magazine "Intertek News." Intertek News delivers information and various topics related to ISO audits, certifications, and verifications. The feature of this issue is titled "Understanding Standard Revisions," where we introduce key points of management system standard requirements that new personnel should first understand in preparation for standard revisions. Additionally, we have included customer case studies, contributions from auditors, and information on certifications and standards, as well as the latest topics, so please take a look.