Aiming for Zero Workplace Accidents! How to Choose the Right Protective Gloves [Environmental Measures VOL.8]

This will focus on cut injuries and chemical damage, which are believed to be common not only in labor accidents but also in near misses, and will explain the characteristics of protective gloves and their proper usage.

Work that requires protective equipment occurs not only in manufacturing but also in various industries. Among the many types of protective gear, gloves in particular come in a wide variety, and there may be cases of improper use, reuse, or instances where protective gloves are not used despite the work being hazardous. However, neglecting such situations leads to the abandonment of [unsafe behaviors] and [unsafe conditions], as discussed in VOL.3, increasing the likelihood of workplace accidents. In 2023, "cuts and abrasions" ranked 5th (5.61%) in workplace accidents, while "contact with harmful substances" ranked 13th (0.45%). However, it is believed that there are potentially many more near misses that did not result in accidents. This time, we will focus on the more frequent incidents of cuts and chemical injuries, discussing the characteristics of different types of protective gloves and their proper usage.

• Safety and consumables
• Disaster prevention supplies
• Safety Supplies

We will introduce the basics of risk assessment and safety protective equipment to ensure the safety of workers.

Since 1988, the number of casualties from workplace accidents has been decreasing, but since 2000, the decline has plateaued. In White Paper Vol. 2 [Winter Season Sees a Surge, Preventing Falls], we addressed the causes and preventive measures for falls, which are the most common workplace accidents. But why do workplace accidents occur in the first place? This time, we would like to focus on protecting the safety of workers and discuss the mechanisms behind workplace accidents and their prevention.

• Safety and consumables
• Disaster prevention supplies
• Safety Supplies

The Ministry of Health, Labour and Welfare has established new regulations to prevent work-related accidents caused by chemical substances.

Starting from April 1, 2024, it will be mandatory for workplaces that handle chemical substances such as sodium hypochlorite (bleach), sodium hydroxide, and potassium hydroxide to require the wearing of protective eyewear. 【Details of the New Regulation】 ■ Workplace Structure 1. Workers handling chemical substances must wear appropriate protective gear, such as protective eyewear. 2. Establishment of a system for self-management. (1) Appoint a chemical substance manager. (2) Appoint a protective gear management officer. ■ Prevention of Direct Contact with Hazardous Chemical Substances When engaging workers in tasks that involve the manufacturing or handling of chemical substances that are skin or eye irritants, corrosive to the skin, or can be absorbed through the skin and cause health issues, it is necessary to require workers to use protective gear to prevent injuries, according to the harmfulness of the substances. For more details, please refer to the materials.

• Safety and consumables
• Disaster prevention supplies
• Safety Supplies

Compatible with a wide range of solvents. Can be used as inner gloves.

【Features】 ■ Compatible with a wide range of solvents ■ Ambidextrous disposable type ■ Can be used as inner gloves ■ European standards EN420/374 *For more details, please refer to the PDF document or feel free to contact us.

• Safety and consumables

A cutter with a safety design that automatically retracts the blade when cutting is finished. It's a precaution against accidents when cutting cardboard and packaging materials!

The safety cutter "Secupro 625" solves the problem of cutting thick materials like cardboard, where "it’s hard to cut without applying force," but "applying force increases the risk of cutting accidents." The "Secupro 625" is designed so that the blade does not extend unless it is held. 【Features】 ■ The blade automatically retracts into the body when it is away from the material being cut. ■ Durable aluminum body. ■ Left-handed compatible. * For more details, please refer to the PDF document or feel free to contact us. * A video demonstrating how the blade automatically retracts is available.

• Work tools

Thin chemical-resistant gloves made with three types of materials and featuring three characteristics!

"Try Lights" are gloves made from three types of materials: natural latex, neoprene, and nitrile, each possessing the three characteristics of "elasticity," "chemical resistance," and "durability." The surface is embossed, making them effective for tasks such as cleaning where items may easily drop. As thin gloves, they offer a wide range of chemical resistance and serve excellently as inner gloves for chemical work that requires thicker gloves. [Features] ■ Three types of materials providing "elasticity," "chemical resistance," and "durability" ■ Slip-resistant processing ■ Wide range of chemical resistance ■ No waterproof powder ■ Surface treated with chlorine for sterilization ■ FDA (U.S. Food and Drug Administration) certified *For more details, please refer to the PDF document or feel free to contact us.

• Safety and consumables

Hotron Inc. has launched its new product, the "Vehicle Count Sensor CCS3"! This product is a ceiling-mounted sensor that combines infrared and radar technology. It reliably detects vehicles in both directions with a single unit, accommodating traffic during congestion and vehicle passing, thus achieving efficient occupancy management in large parking lots. Additionally, it can be utilized for exit warning purposes in addition to vehicle counting, contributing to the safe and smooth operation of parking facilities. 'Features' - Improved detection performance against changes in road surface during rainy weather by using both infrared and radar. - Equipped with IP67 waterproof and dustproof performance, making it effective even in salt damage areas. - Various settings can be configured from a dedicated app (for Android devices), with current settings easily visible at a glance. - The base dimensions are the same as the previous model "CCS2," allowing for smooth replacement of existing equipment. *For more details, please refer to the product information, catalog download, or contact us.*

The signing methods for electronic contracts (party type and witness type) are directly linked to the strength of their legal effectiveness. In this article, we will outline the reasons why the more stringent "party type" has been difficult to popularize until now. ---【Conclusion of this article】-------------------------------- • There are two signing methods for electronic contracts: "witness type" and "party type," which differ in the strictness of identity verification. • The main reasons why the party type has not spread are the three factors of "effort, cost, and the structural risk of entrusting a private key." • However, with the spread of public personal authentication (JPKI) using My Number cards, these three barriers are beginning to crumble. -------------------------------------------------------- The full text of the article can be accessed from the "Related Links."

Seven Corporation has started offering the "SeveNavi AI Cleaning Diagnosis Service," which supports the organization and improvement of cleaning challenges in manufacturing environments. Organizing cleaning challenges with AI and visualizing the next steps In manufacturing cleaning, various factors need to be considered, including the material of the object, type of dirt, adhesion state, currently used cleaning agents, working time, safety, and equipment conditions. On the other hand, there are also several challenges faced on-site, such as: - Unable to determine if the current cleaning method is appropriate - Wanting to reduce cleaning time and labor - Concerns about the safety of cleaning agents and their impact on materials - Wanting to compare with another cleaning method but unable to set test conditions - Not being able to utilize past cases and knowledge for improvement activities SeveNavi organizes information such as the object, dirt, current cleaning methods, and site photos using AI, clearly presenting the applicability of cleaning methods, points of caution, missing information, and how to proceed with comparative testing. If you have any challenges regarding reviewing current cleaning methods, comparing new cleaning methods, or reducing cleaning time and labor, please feel free to consult with us.

An online seminar will be held for design, purchasing, and DX promotion personnel considering the introduction or switch to new CAD systems, featuring the DWG-compatible 2D CAD "ARES." Participants can review content directly related to business improvement, including a comparison of features and performance with AutoCAD, automation using the CAD-specific AI "A3," automatic generation of DWG drawings from BIM data, and new ways of working in the cloud. ■ Date and Time: September 17, 2026 (Thursday) 13:30 - 15:00 ■ Format: Online (with archive viewing available) ■ Participation Fee: Free ■ Recommended for: - Those considering switching from AutoCAD - Those interested in AI utilization and automation in CAD operations - Those looking to streamline collaboration with BIM - Those seeking an environment where drawings can be edited regardless of location As a viewing benefit, a free "ARES Trinity Utilization Manual" (worth 6,000 yen) will be provided. Additionally, if you apply through the URL in the related links, our company, Keynos Logic, will consistently support you from post-seminar implementation considerations to estimates and support after operation begins. If you are interested in ARES, feel free to start by participating in this seminar.

On August 28, 2026 (Friday), I participated in the "AMD Embedded Computing Summit Tokyo 2026" and showcased a "Gesture Demo" as a partner of AMD. The demonstration introduced a configuration that combines gesture recognition using OpenCV, status reporting with LLM, and one-axis motor control using INtime 7.2 and RSI-ECAT, enabling collaboration between AI, image processing, and real-time control on a single PC. We presented a next-generation PC-based industrial control system that integrates AI, image processing, and real-time control on one PC. <Overview of Demo Participation> https://www.mnc.co.jp/INtime/AMDxINtime/AMDEcsTokyoResults.html <Actual Demo Video> https://youtu.be/JmZke75_y0s <AMD CPU + INtime RTOS Introduction Page> https://www.mnc.co.jp/INtime/AMDxINtime/amdxintime.html #PC #RealTimeOS #IndustrialPC #AI