We have started publishing basic knowledge materials for beginner-friendly aluminum saw blades!

D2 type chip saw with low burr and a focus on fine finish! Suitable for cutting thin aluminum building materials, sashes, and frame profiles.

The blade type that cuts evenly on both sides allows for aluminum sashes and extruded materials to be cut with minimal burrs and a clean finish.

• Work tools

D2 type chip saw with a focus on low burr and fine finish! Suitable for cutting thin aluminum building materials, sashes, and frame profiles.

The inclined blade (staggered blade) cuts aluminum sashes and extruded materials with minimal burrs and produces a clean cut surface by cutting evenly from both sides. ■Target materials - Aluminum sashes for construction materials - Aluminum profiles - Small diameter copper pipes

• Woodworking machines, instruments, and tools

3DX type chip saw that enables high-speed cutting with low cutting resistance! It accommodates a wide range from aluminum billets to construction material frames.

This is a cost-effective chip saw with lower cutting resistance compared to chisel blades and high-low blades, which helps reduce power consumption.

• Work tools

High straightness and smooth chip discharge. The D4 saw blade is optimal for copper sheet materials.

The D4 blade type, which excels in straight cutting, allows for smooth cutting of copper busbars. It is designed to minimize workpiece jamming during copper plate cutting. The chips are divided into three parts to facilitate easy chip discharge.

• Woodworking machines, instruments, and tools

High straightness and smooth chip discharge. The D4 saw blade is ideal for thick aluminum extrusions, rods, and plates.

The D4 blade type, which excels in straight cutting, efficiently cuts through thick aluminum and copper materials. It divides the chips into three parts to efficiently discharge the shavings.

• Work tools

An article has been published about the case of introducing the expense reimbursement system "Rakuraku Seisan" at TSP Corporation. ~ In the case of TSP ~ Before the introduction, there were challenges such as dealing with the "paper" sent from various locations and the reliance on specific individuals for the tasks. After the introduction, the input and checking of FB data, which used to take 2 to 3 hours, can now be completed in just 5 minutes. Additionally, the mindset of the accounting department, which was previously reliant on manual entry, has changed. [Case Overview] ■ Challenges before introduction - Dealing with "paper" sent from various locations, reliance on specific individuals ■ Key points of introduction - A robust support system for setup and operation - Easy to start from a small scale both financially and functionally *For more details, please refer to the related links or feel free to contact us.

The facility operating the nurse call system has made the bed exit sensor wireless, allowing it to notify in conjunction with the nurse call. By simply connecting the mat sensor "Foldable Thin Matt-kun," the body movement call "Ugo-kun," and the wheelchair body movement call "Ayumi-chan" to the transmitter HB-RS, you can make the bed exit sensor wireless. The infrared sensor "Just Place Pole-kun" has the transmitter HB-RS built-in. 【Features】 ○ Wireless conversion by simply connecting existing sensors to the transmitter HB-WSK. ○ The bed exit sensor notifies wirelessly in conjunction with the nurse call. ○ Up to 5 transmitters can be registered with one receiver. ○ The communication distance between the transmitter and receiver is approximately 10 meters. ◎ For more details, please contact us or download the catalog.

Full and empty management refers to the real-time display of parking availability and the management of efficient use of parking spaces. By utilizing Hotron's sensors, drivers can quickly discover available parking spaces, achieving efficient parking lot operations. ■ For large parking lots, the "floor management method" and "block management method," which focus on cost reduction, are recommended. Sensors are installed at regular intervals to count the number of vehicles passing through. This method offers the advantage of easy installation and low costs. 【Target Products】 - Vehicle Count Sensor CCS2 - Ultrasonic Sensor HM-UX2/UW2 ■ For smaller scale operations, the "space management method," which installs sensors in each parking space to display availability with high accuracy, is recommended. By ensuring accurate full and empty displays, it helps prevent unnecessary entry of new vehicles and enables safe parking lot operations. 【Target Products】 - Occupancy Detection Sensor HM-UX2/UW2 - Occupancy/Pass Detection Sensor HM-LC6 - Occupancy Detection Sensor HM-LC7/LC7-FLS - Occupancy/Pass Detection Sensor HM-S6 - Occupancy Detection Sensor HM-S8

Castem Co., Ltd. will exhibit at the "Monozukuri World Osaka - Mechanical Components Technology Exhibition" held at Intex Osaka from Wednesday, October 1 to Friday, October 3, 2025. We will showcase lost-wax precision casting and MIM (Metal Injection Molding) products, as well as introduce our new technology, mold-less casting "Digital Cast." In addition to our popular casting demonstrations, we will present case studies on solving issues related to metal parts. Please utilize our "Technical Consultation Booth" to learn about optimal manufacturing methods tailored to your needs, from ultra-small lots to mass production. 【Exhibition Overview】 Dates: October 1 (Wed) - October 3 (Fri), 2025, 10:00 AM - 5:00 PM Venue: Intex Osaka (1-5-102 Nanko-Kita, Suminoe-ku, Osaka City, Osaka Prefecture) Exhibition Booth Number: Hall 6, B Hall 51-1 Pre-registration allows for smooth entry. It is convenient to register via the URL below before your visit. We sincerely look forward to your attendance. https://www.manufacturing-world.jp/osaka/ja-jp/register.html?code=1431877272389396-VEK

From November 11, 2025 (Tuesday), at Pacifico Yokohama, we will be exhibiting at interOpto2025 / Light and Laser Science and Technology Fair (organized by the Optical Industry Technology Promotion Association / Optronics Corporation) with a focus on: - UV-transmitting glass that can be molded - Diffusion glass that can uniformly diffuse incident light - A double-sided lens array that is molded without lamination 【About the Exhibition】 Event Name: interOpto2025 / Light and Laser Science and Technology Fair UV Fair Date: November 11 (Tuesday) to 13 (Thursday), 2025 Opening Hours: 10:00 AM to 5:00 PM Venue: Pacifico Yokohama Exhibition Hall C Booth Number: C-15 Organizer: Optical Industry Technology Promotion Association / Optronics Corporation Official Website: https://www.optronics.co.jp/interopto/ We invite everyone attending this exhibition to visit our booth "Gosuzumi Seiko Glass." We sincerely look forward to meeting you on-site.