"High-temperature heating, tensile compression, and in-situ observation" with atmosphere control / High-temperature tensile compression observation device "CATY-T3H" achieves space-saving with a compact tabletop design.

Tests can be conducted while observing the condition of the material surface [using a dual-swing crosshead], keeping the sample position centered to avoid missing any changes!

The "CATY-T3H SYSTEM" is a tabletop high-temperature tensile observation device that allows for thermal fatigue testing while observing the condition of the sample surface in real-time. It can be operated easily and supports high-temperature and high-speed heating. The adoption of a dual-swing crosshead ensures that the sample's position remains centered, even with expansion and contraction, minimizing any displacement of the observation point. By combining it with optional units, it can also accommodate tests such as bending observation. 【Features】 ■ Capable of high-temperature and high-speed heating up to 1500°C * However, this depends on the shape and thermal capacity of the sample. ■ Suitable for testing not only metallic materials but also composite materials of surface-mounted components ■ Enables stress measurement, low-cycle fatigue testing, and creep testing in gas flow or vacuum conditions ■ Realizes combined testing of thermal fatigue under stress and real-time observation * For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Steel

Minimize work inside the glove box ◎ Solid electrolyte material screening / Impedance evaluation by temperature characteristics ◎ Multiple uniform, short time, and accurate test evaluation

It excels in material screening of solid electrolytes and impedance evaluation according to temperature characteristics! ▼Features▼ 1. Reproduces various heating patterns of inorganic electrolyte heating and sintering processes in a short time - Temperature can be adjusted with an accuracy of ±1°C within a temperature range of 50°C to 1200°C - The heating rate can reach a maximum of 300°C/min, allowing for various heating patterns to be tested in a short time from room temperature 2. Efficient simultaneous evaluation of impedance measurements for lithium-ion conductivity (conductivity) - Structure allows for heating with electrodes attached to both ends of the coin cell - Coin cell holder is prepared for 4 slots - Uniform heating/measuring of 4 samples simultaneously under the same conditions - Various coin cell diameters available from Φ20 to Φ8mm 3. Simple operation and design that prevents exposure to the atmosphere / atmosphere control - Work inside the glove box is limited to sample set only - Inside the quartz tube, a quartz coin cell holder is held, and only the coin cell is accurately heated - Light heating from outside heats the completely sealed transparent quartz tube - Gas introduction system and atmosphere control during heating are also easy For more details, please contact us.

• Batteries and Capacitors
• Fuel Cells
• Other Hydrogen/Fuel Cells

We would like to inform you that, in order to further strengthen and enhance our sales and service operations, there will be changes to our Nagoya Sales Office as of April 1st, as detailed below. ■ Relocation of Nagoya Sales Office 【New Address】 〒460-0003 6th Floor, Sando Building, 1-7-27 Nishiki, Naka Ward, Nagoya City, Aichi Prefecture TEL: 052-212-6520 / FAX: 052-212-6521 *Please note that the TEL and FAX numbers will also change. Taking this opportunity, all of our staff will continue to make even greater efforts. Please feel free to contact us.

We will introduce the implementation results of the sensor technology developed by the Hotron Group, which has been cultivated over more than half a century, through customer case studies. In addition to automatic door sensors, we also offer a wide range of vehicle detection sensors and nursing/care sensors. We have many implementation examples available, so please take a look at the case study page.

iPick Co., Ltd., a partition manufacturer, will explain the definition of non-combustible materials under the Building Standards Act and their importance in office interiors. Fire-resistant materials are classified into three categories: non-combustible, quasi-non-combustible, and flame-retardant, based on safety during a fire. At iPick, we handle aluminum partitions that have received non-combustible certification, demonstrating high fire resistance, which is required by "interior restrictions" depending on the size and use of the building. Selecting appropriate materials is crucial not only for protecting the lives of employees but also from the perspective of asset protection and business continuity planning (BCP). We propose the creation of safe spaces that balance compliance with regulations and design. ＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊ For the design and construction of interior partitions from offices to toilet booths, leave it to iPick, the partition specialist manufacturer! "We are accepting reservations for live office and showroom tours." 6F NMF Kanda Iwamotocho Building, 3-8-16 Iwamotocho, Chiyoda-ku, Tokyo For inquiries, feel free to contact our toll-free number 0120-020-720 (Weekdays 10:00 AM to 5:00 PM)!

JECA FAIR 2026 will be exhibiting at the 74th Electrical Installation Industry Exhibition. Dates: May 27, 28, 29 Venue: Tokyo Big Sight, Halls 1, 2, 3, and 8 We look forward to your visit.

The JRE Disaster Assessment Support System Gragram, jointly developed by Hakusan Industrial Co., Ltd. (Headquarters: Fuchu City, Tokyo, President: Minoru Yoshida https://www.hakusan.co.jp/) and JR East Japan Architectural Design Co., Ltd. (Headquarters: Shibuya City, Tokyo, President: Yoshihiko Ito https://www.jred.co.jp/), has been implemented in all buildings of the TAKANAWA GATEWAY CITY, which will have its grand opening on March 28, 2026, and OIMACHI TRACKS, which will open to the public. For more details, please refer to the link below.