Circular Saw Cutting Machine Model Selection Table

The JCU-510D achieves precise angle cutting with free rotation of up to 60 degrees in either direction. Its compact design accommodates cutting of aluminum profiles, plastics, and plywood.

The "JCU-510D model" is a cutting machine that allows for easy operation and safe, precise free-angle cutting. It enables free angle settings from -30° to +30°, with fine adjustments possible in high resolution of 0.05-degree increments. During cutting, it is secured with a cover that also serves as an upper clamp, and it allows for chip suction by a dust collector. With a compact design suitable for space-saving installation, it accommodates a wide range of materials such as aluminum, resin, and wood, and can also be connected to an automatic length setting device (auto-positioner).

• Construction materials

Cutting at a height of 120mm × width of 450mm in one go! In addition to angle cutting, it can also perform groove cutting with adjustable blade height, making it a free cross-cut saw.

The "ACGII" is a manual circular saw cutting machine that can swing the radial arm left and right to make various angle cuts. The swing angle of the left and right arms can go up to 60°, and the axis tilt angle can be adjusted up to 45° to the right, making it ideal for cross-cutting long materials. The circular saw is positioned on a table and passes through the workpiece by hand guidance. Instead of moving the workpiece like a tilting table, the circular saw can be moved to match the cutting length while keeping the workpiece fixed. It can be placed along a wall when space is limited. The circular saw axis can be raised and lowered, allowing for groove processing as well. 【Features】 ■ Capable of making right-angle cuts, various angle cuts, and groove processing ■ The guide shaft for the tool feed is made of hardened and polished material ■ Groove cutting can be performed by raising and lowering the circular saw axis Options: - Sliding back support ruler - Angle digital display - Rear chip collection cover *For more details, please refer to the PDF document or feel free to contact us.

• Gates, walls and fences

An article has been published about the case of introducing the expense reimbursement system "Rakuraku Seisan" at TSP Corporation. ~ In the case of TSP ~ Before the introduction, there were challenges such as dealing with the "paper" sent from various locations and the reliance on specific individuals for the tasks. After the introduction, the input and checking of FB data, which used to take 2 to 3 hours, can now be completed in just 5 minutes. Additionally, the mindset of the accounting department, which was previously reliant on manual entry, has changed. [Case Overview] ■ Challenges before introduction - Dealing with "paper" sent from various locations, reliance on specific individuals ■ Key points of introduction - A robust support system for setup and operation - Easy to start from a small scale both financially and functionally *For more details, please refer to the related links or feel free to contact us.

The facility operating the nurse call system has made the bed exit sensor wireless, allowing it to notify in conjunction with the nurse call. By simply connecting the mat sensor "Foldable Thin Matt-kun," the body movement call "Ugo-kun," and the wheelchair body movement call "Ayumi-chan" to the transmitter HB-RS, you can make the bed exit sensor wireless. The infrared sensor "Just Place Pole-kun" has the transmitter HB-RS built-in. 【Features】 ○ Wireless conversion by simply connecting existing sensors to the transmitter HB-WSK. ○ The bed exit sensor notifies wirelessly in conjunction with the nurse call. ○ Up to 5 transmitters can be registered with one receiver. ○ The communication distance between the transmitter and receiver is approximately 10 meters. ◎ For more details, please contact us or download the catalog.

Full and empty management refers to the real-time display of parking availability and the management of efficient use of parking spaces. By utilizing Hotron's sensors, drivers can quickly discover available parking spaces, achieving efficient parking lot operations. ■ For large parking lots, the "floor management method" and "block management method," which focus on cost reduction, are recommended. Sensors are installed at regular intervals to count the number of vehicles passing through. This method offers the advantage of easy installation and low costs. 【Target Products】 - Vehicle Count Sensor CCS2 - Ultrasonic Sensor HM-UX2/UW2 ■ For smaller scale operations, the "space management method," which installs sensors in each parking space to display availability with high accuracy, is recommended. By ensuring accurate full and empty displays, it helps prevent unnecessary entry of new vehicles and enables safe parking lot operations. 【Target Products】 - Occupancy Detection Sensor HM-UX2/UW2 - Occupancy/Pass Detection Sensor HM-LC6 - Occupancy Detection Sensor HM-LC7/LC7-FLS - Occupancy/Pass Detection Sensor HM-S6 - Occupancy Detection Sensor HM-S8

Castem Co., Ltd. will exhibit at the "Monozukuri World Osaka - Mechanical Components Technology Exhibition" held at Intex Osaka from Wednesday, October 1 to Friday, October 3, 2025. We will showcase lost-wax precision casting and MIM (Metal Injection Molding) products, as well as introduce our new technology, mold-less casting "Digital Cast." In addition to our popular casting demonstrations, we will present case studies on solving issues related to metal parts. Please utilize our "Technical Consultation Booth" to learn about optimal manufacturing methods tailored to your needs, from ultra-small lots to mass production. 【Exhibition Overview】 Dates: October 1 (Wed) - October 3 (Fri), 2025, 10:00 AM - 5:00 PM Venue: Intex Osaka (1-5-102 Nanko-Kita, Suminoe-ku, Osaka City, Osaka Prefecture) Exhibition Booth Number: Hall 6, B Hall 51-1 Pre-registration allows for smooth entry. It is convenient to register via the URL below before your visit. We sincerely look forward to your attendance. https://www.manufacturing-world.jp/osaka/ja-jp/register.html?code=1431877272389396-VEK

From November 11, 2025 (Tuesday), at Pacifico Yokohama, we will be exhibiting at interOpto2025 / Light and Laser Science and Technology Fair (organized by the Optical Industry Technology Promotion Association / Optronics Corporation) with a focus on: - UV-transmitting glass that can be molded - Diffusion glass that can uniformly diffuse incident light - A double-sided lens array that is molded without lamination 【About the Exhibition】 Event Name: interOpto2025 / Light and Laser Science and Technology Fair UV Fair Date: November 11 (Tuesday) to 13 (Thursday), 2025 Opening Hours: 10:00 AM to 5:00 PM Venue: Pacifico Yokohama Exhibition Hall C Booth Number: C-15 Organizer: Optical Industry Technology Promotion Association / Optronics Corporation Official Website: https://www.optronics.co.jp/interopto/ We invite everyone attending this exhibition to visit our booth "Gosuzumi Seiko Glass." We sincerely look forward to meeting you on-site.