エム・ティ・ケイ List of Products and Services

Check the direction of the flooring installation and the connection points in both vertical and horizontal directions, and consider the fixing points of the flooring material. Install it with a layout spaced at 1 shaku (303 mm) intervals. *For details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The controllers have been installed in each room, with four units for one channel. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

Did you know that underfloor heating can be installed from beneath the floor? No need to move furniture, and you can maintain your usual lifestyle! The "underfloor method," where an electrician works underneath the floor to install the heating, allows for easy renovations. 1. The existing floor can be used as is. 2. Reduces stress by eliminating the need to move furniture. 3. Significant savings on material and construction costs for new flooring. *Please note that installation may not be possible depending on the environment and conditions under the floor. Feel free to consult us. *You can check the installation process and costs in the catalog.

• Floor heating (electric, panel, storage type, etc.)

The existing underfloor insulation is properly installed, so there will be no heat loss through the floor. Connect the sheet wiring and the dedicated connection cable (extension wire) under the floor, and apply waterproof tape (self-fusing butyl) for waterproofing on the connectors. Once the primary power supply and the wiring from the sheet are connected to the controller and mounted on the wall, the underfloor heating installation is complete. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The controller installation is complete. It can be used anytime once the flooring work is finished. An apartment with floor heating is nice. *For details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

20 sheets of flooring have been installed in the living room, dining room, and kitchen. The flooring finishing in the kitchen area has begun, and the floor heating-specific adhesive (MD adhesive) is being applied. *MD adhesive is a solvent-free polyurethane resin-based adhesive. The flooring in the kitchen area has been completed, and the insulation and synthetic resistance value measurements after the flooring completion have also been successfully finished. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The design ensures that the transition space between the kitchen, dining, and living areas warms up continuously. The controller has been centralized on the dining room wall. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

We will arrange the sheets, fit the wiring into the grooves, and perform waterproofing. The controller will be consolidated on the kitchen wall, and that will be the end of it. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The insulation and combined resistance values have been measured, and the installation work is complete. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

This is a living and dining area with 16 sheets of 3000mm long cork sheet laid out. Above the kitchen, there is a loft in the open living and dining area, and most importantly, cork sheets are installed on the floor. Since it warms from the floor, you can feel secure even on cold days. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

Here are the construction steps: 1. Layout the sheets and drill holes for wiring. 2. Drill a hole from the wall where the controller will be mounted to the underfloor. 3. Apply floor heating-specific adhesive about 3 centimeters from the gap between the sheets. 4. Secure the flooring finish material without damaging the sheet area. 5. After completing the floor, gather the controller wiring and measure the installation position to finish. 6. Once the interior is finished and the controller is installed, the floor heating work is complete. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

Connect the wiring of the sheet under the bed and install the controller to complete the setup. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The carpenter finished the flooring in the living and dining area in about two hours. They will connect the wiring under the floor and measure insulation and combined resistance on the controller side. Once the interior is finished, they will open a hole (100×100) in the wall to install the controller. To ensure the opening is correct, it’s advisable to measure the center of the opening based on the floor and the left and right walls and keep a record for peace of mind. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

The wiring is done under the floor, and the controller is installed, so it's complete. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

This time, we received a request for the installation of a controller for underfloor wiring connections by a carpenter and have completed the work. We connected the wiring of the Pokara sheet under the floor. The wiring of the controller is connected to the wiring of the Pokara sheet. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

As you all know, since it is electric, it is also suitable for spot heating in areas like washrooms and toilets. The installation work for the electric sheet was completed in about 1 to 2 hours. It’s nice to have a warm floor when you get out of the bath on a cold winter day. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

Connect the wiring of the installed sheet under the floor. An insulation measurement of 50MΩ or more is considered normal. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will guide you through the work process. 1. Layout the sheets and drill holes for wiring. 2. Remove the base plywood, connect the wiring, and wrap it with self-fusing butyl. 3. The wall is completed, so install the controller. The floor heating work is now finished. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

1. We will create a wiring route on the floor. 2. We will dig a groove from the socket sheet to the controller to create the route. 3. We will pass the wiring through the groove, implement waterproof measures, pull the wiring to the controller installation position, and then install the controller to complete the process. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

Due to the inability to install wiring under the floor, we created grooves for wiring in the base plywood and conducted the installation with above-floor wiring. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The installation was done in the living room, dining room, and kitchen. We will drill holes for wiring just like the plywood base and lay down the flooring sheet. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will introduce the work process. 1. We will drill a hole (about 60mm) to pass the wiring for the Poca sheet under the floor. 2. Since there is no access panel under the floor, we will remove part of the floor structure to run the wiring. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will publish the installation scenery. The wiring will be connected under the floor and laid out to the installation position of the controller. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will publish photos of each installation. Once the floor heating installation work is completed, it's the carpenter's turn. The sheets arranged at one-foot intervals are fixed with a floor heating-specific adhesive and a stapler. Once the walls are finished and the controller is installed, the work is complete. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We have installed floor heating in five areas: the living room, dining room, kitchen, bathroom, and Western-style room. The system is divided into five zones, allowing for individual control. We will drill holes for the sheet wiring, drop the wiring under the floor, and connect it underneath. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The waterproof treatment for the underfloor connection is perfect. *For details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

Here is the introduction to the work process. 1. Since the second floor cannot be accessed from below, we will cut the wiring route on the floor using a circular saw. 2. We will install the underfloor heating mat. This room will have an underfloor heating area of 3000mm x 3000mm. 3. We will run the secondary side line of the underfloor heating up to the wall where the controller will be installed. 4. Later, once the wall is completed and the wallpaper is finished, we will install the controller. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

1. Cut the sheet into sections of 1 shaku and drill holes for the wiring. (Dig a groove about 12 mm deep with a 60 mm diameter and drill a 15 mm hole for wiring.) 2. Lay the sheet and seal the holes where the wiring passes through with waterproof tape. 3. Connect the wiring of the sheet and the attached cable (additional wiring) under the floor, wrap the connection with self-fusing tape for waterproofing. 4. Once the work below is completed, perform insulation measurement and measure the synthetic resistance; if there are no abnormalities, the floor heating installation work is finished. *For details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

The controller has been installed and is now in trial operation. It reached a temperature of 27° in about 15 to 20 minutes. It's nice and warm. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

1. We will address the steps and unevenness of the underfloor plywood and mark every 1 shaku (30 mm) to drill holes for dropping the wiring of the sheet under the floor. 2. We will lay out the sheets, drop the wiring under the floor, and seal it with waterproof tape. 3. We will connect the wiring of the sheet and the secondary side of the controller under the floor. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

During the large pull, three sheets of 75 millimeters in length were arranged. Once the installation of the sheets is completed, insulation will be installed to finish up. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

〈Example 2〉 A sunken kotatsu installed on a stage one meter high on the same floor as the living room. A sunken kotatsu that is elevated by one step. We laid down a heating sheet around it and at the feet. Since the body warms up from two places, the feet and the bottom, it feels cozy. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

〈Example 1〉 We assembled a frame for a sunken kotatsu on the living room floor and laid down a plastic sheet around it and at the feet. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

1. We will layout the sheets and drill holes to drop the wiring under the floor. 2. We will arrange and line up the sheets. 3. We will line them up inside the layout at one-foot intervals. 4. We will seal the holes with waterproof tape, secure the sheets, and the sheet installation will be complete. 5. Under the floor, we will connect the sheets to the dedicated jumper wires with connectors and wrap them with self-fusing tape. 6. Once the wall work is completed, we will install the controller and finish up. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

This is the combination with the highest order rate at our company. *For details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

This is a general residential living room. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

The construction involved two rooms. One room had the floor removed, while the other had a new floor installed over the existing one. Since there were many sheets to work with, we collaborated with the craftsmen and managed to complete the sheet installation in one day. First, we carried out the usual construction method, which involved laying sheets on the substrate after removing the flooring cleanly. The other method was for the overlapping installation. In this case, the space under the floor was too narrow to access, so we couldn't do the wiring underneath; instead, we created a wiring route on the substrate floor and did the wiring above the floor. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

This time it's a renovation of an apartment, so the concrete is exposed. We will apply a 12mm underfloor heating substrate called Zetron on top of this, enhancing the insulation performance before installing the underfloor heating system itself. We will directly adhere it to the concrete slab with a special adhesive. Zetron is very lightweight and can be easily cut with a utility knife, making the installation very easy! Next, we will also attach the underfloor heating system using a special adhesive for underfloor heating. We will apply the adhesive in beads and then spread it with a brush. Thus, today the underfloor heating renovation of the apartment with a view of the sea has been completed. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

A warm spot at the feet in the kitchen. Having a timer is also nice. If you set the timer 30 minutes before waking up, your feet will be warm while cooking. I definitely recommend it. *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities

If so many sheets are included, it will be warm! The quick startup is also one of the advantages of PTC. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

It's impressive to see so many Poka sheets lined up. This time, we also installed the controller. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will post photos of the construction and photos after the construction. You can really feel the warmth. *For more details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

We will post photos of the construction and photos after the construction. This will make it warmer, won't it? *For details, please download the PDF or feel free to contact us.

• Heating and cooling equipment and facilities

It's a 1K room, but I've laid out insulation throughout to combat the cold. At the owner's request, it's connected to a gas water heater for the "pokara onsui" (a type of heated water system). I've also thoroughly insulated the area under the kitchen. And at the entrance as well. This is what you call whole-house heating! This room has a loft, so the ceiling is higher. This is where the "pokara onsui" comes into play! With this, it's comfortable! No more cold! Wishing you a cozy winter.

• Heating and cooling equipment and facilities

Everyone! Do you know about herringbone? It seems to refer to a pattern that resembles the bones of a fish, specifically the bones of a herring! Actually, more and more people are building homes with herringbone flooring lately, and we have received many inquiries about it at our company. "Can your underfloor heating work with herringbone?" (Fukushima dialect) Yes! It's perfectly fine! "That's great! Other underfloor heating systems can't use it!" Leave it to us! We specialize in underfloor heating! So, we have been adopted! *For more details, please download the PDF or feel free to contact us.*

• Heating and cooling equipment and facilities