ウィズソル List of Products and Services

The digital radiography inspection system "CR" uses imaging plates (IP) to digitize accumulated radiation image information. This allows for consistently stable image quality. The readable IP sizes are standard up to 35.4×43 cm and long type up to 7×152 cm, with readable pixel sizes of 25, 50, 100, and 200 μm. 【Features】 ■ High sensitivity allows for reduced radiation exposure time ■ Rich image processing due to wide gradation ■ Easily viewable images tailored to inspection purposes through computer processing ■ Utilization of data and digital storage through digital images *For more details, please refer to the PDF materials or feel free to contact us.

• Other Software

The "IRIS" water immersion type ultrasonic wall thickness measurement device for heat exchange tubes accurately measures the remaining wall thickness from the inner surface of the tube using ultrasonic waves. Ultrasonic waves are transmitted and received to the pipe wall using a reflective mirror at the tip of the turbine. The turbine rotates at high speed due to water pressure, and the mirror also rotates simultaneously, allowing for data to be obtained around the entire circumference. 【Features】 ■ Real-time measurement while viewing cross-sectional images ■ Ability to distinguish between inner and outer surfaces of reduced thickness areas ■ Integrated structure for easy transportation to and from the site, excellent operability on site *For more details, please refer to the PDF document or feel free to contact us.

• Other measuring instruments

The high-speed immersion ultrasonic thickness measurement device for heat exchange tubes, 'UTIS', is a system that confirms the wall thinning of the inner and outer surfaces of heat exchange tubes at high speed. It allows for accurate understanding of wall thinning conditions through full circumference and full length measurements. Visual judgment is also possible through measurement results with color mapping. The encoder enables the identification of wall thinning locations, and the acceleration of mirror rotation significantly improves the extraction speed. Additionally, the inner and outer surface amplifier switching function allows measurements down to a remaining wall thickness of 0.6mm. 【Specifications (partial)】 ■ Applicable pipe inner diameter: Φ9.5 to Φ50mm ■ Measurable wall thickness: 0.6 to 10mm ■ Probe frequency: 7.5 to 15MHz ■ Repetition frequency: 10 to 20kHz *For more details, please refer to the PDF document or feel free to contact us.

• Other measuring instruments

The pipe support contact area thinning inspection device "U-Rack" is a device that inspects the external corrosion of the contact area without the need to jack up the pipes. The probe is placed on the pipe, and ultrasonic waves are transmitted and received in the circumferential direction (two directions), while the probe is continuously scanned in the axial direction of the pipe. The fluctuations in the received transmitted wave levels are recorded, and the thinning rate is evaluated from the transmitted wave levels. 【Features】 ■ No need to jack up the pipes ■ Inspection can be performed while in operation ■ The transmitted wave levels during the axial scanning of the probe are automatically recorded, allowing for objective evaluation ■ Applicable pipes range from 2B to 12B (carbon steel pipes) ■ Up to 20 inspection points can be inspected per day *For more details, please refer to the PDF document or feel free to contact us.

• Other measuring instruments

The manual scanning continuous plate thickness measurement device 'UDP-M1' is designed to confirm thickness variations along the same line where material reduction is anticipated. It is effective for inspecting corrosion on the backside of piping (including elbows) and flat plates. Previously, thickness measurements were taken at points, but now linear measurements can be easily performed. Additionally, we also offer the 'UDP-M2', which allows for an understanding of material reduction over a surface and provides visual judgment through color mapping. 【Features of UDP-M1】 ■ The encoder allows for the identification of reduction locations. ■ Four magnetic wheels securely adhere to the inspection object, enabling manual scanning. ■ The contact medium can be automatically supplied with water by a pump, allowing for stable measurements. ■ The measurement pitch is as small as 1mm, improving the detection rate of reduced areas. *For more details, please refer to the PDF document or feel free to contact us.

• Other measuring instruments

The tank bottom plate continuous thickness measurement device "UDT-48" is an ultrasonic continuous thickness measurement device that has obtained performance evaluation certification from the Hazardous Materials Safety Technology Association. (January 16, 2012, Safety Evaluation No. 0063) It allows measurements from the coating surface and can measure a width range of approximately 360mm in a single run. It is the successor to "UDT-24," featuring advanced hardware and software technology. 【Features】 - Accurate understanding of thinning conditions through full surface measurement - Visual judgment possible through color mapping - Applicable for safety inspections - Improved detection accuracy of natural corrosion (back side) due to enhanced probe design - Increased efficiency of verification work through full waveform capture functionality - Improved operability and reduced areas where measurement is not possible due to miniaturization and lightweight design of the device *For more details, please refer to the PDF document or feel free to contact us.

• Other measuring instruments

The pipe thickness measurement device "UDP-48" is an ultrasonic continuous thickness measurement device that enables measurements of approximately 500mm in width in a single run. It excels at inspecting large pipes, tank side plates, and other objects with a wide measurement range, particularly for detecting corrosion on the backside. Additionally, we offer the palm-sized portable UDP type "UDP-8" and the "UDP-24," which allows for easy pipe inspections with automatic operation. 【Features of UDP-48】 ■ Can be applied to narrow areas with a scanning jig height of approximately 60mm ■ Adheres to the target object with a magnetic roller and moves in a straight line manually ■ Contact medium is applied using a spray or water pump ■ Efficiency in verification tasks through full waveform recording functionality ■ Visual judgment is possible through numerical display and color mapping *For more details, please refer to the PDF materials or feel free to contact us.

• Other measuring instruments

Wizsol is a company that plays a role in ensuring that various facilities, from industrial infrastructure to social infrastructure, can operate safely and stably through preventive maintenance and corrective maintenance, as well as quality assurance in the manufacturing processes of steel structures and other materials. Our mission is to provide existing and new inspection technologies and heat treatment technologies to contribute to the maintenance and development of a safe and secure society. This document includes various steel structures, starting with the tank visual inspection robot "i-ROBO," which safely conducts visual inspections using an autonomous camera robot, as well as continuous pipe thickness measurement devices and manual scanning continuous thickness measurement devices. [Contents (partial)] ■ Tank visual inspection robot "i-ROBO" ■ Continuous pipe thickness measurement device "UDP-48" ■ Continuous tank bottom plate thickness measurement device "UDT-48" ■ UDP-24 (applicable to side plates, roof plates, and chimneys) ■ Manual scanning continuous thickness measurement device "UDP-M1" *For more details, please refer to the PDF document or feel free to contact us.

• others

Withsol Co., Ltd. is dedicated to supporting and safeguarding industrial infrastructure such as plants and power generation facilities, social infrastructure that is essential for daily life, and Japan's manufacturing, which we take pride in, through quality control and safety assurance. We are committed to continuous technical training and the development of new technologies and new equipment. Our "non-destructive testing," which diagnoses without damaging objects, meets the needs of clients with unique equipment and high-level technology to ensure the maintenance of highly public facilities and the integrity of manufactured products. [Features] - Diagnosis with a scientific approach without damaging objects - Responding to client needs with unique equipment and high-level technology *For more details, please refer to the PDF materials or feel free to contact us.

• others

The "i-ROBO" is a visual inspection robot for tank measurement plate reinforcement weld areas and various steel structures. Equipped with automatic driving sensors, gyro sensors, and collision avoidance sensors, it achieves safe autonomous operation through multiple sensors. Operation, visual inspection, and recording can be done safely from the ground, eliminating the need for scaffolding. Remote switching between automatic and manual operation is possible. 【Features】 ■ Adsorption using permanent magnet tires (adsorption force of 60 to 100 kgf) ■ Cameras mounted on five joint tips ■ Real-time video streaming for visual inspection and continuous photo recording ■ Full-circle imaging can be stored as a record (in the case of tanks) ■ Battery-powered, eliminating the need for AC 100V *For more details, please download the PDF or feel free to contact us.

• others