nozzle(3m) - List of Manufacturers, Suppliers, Companies and Products

Last Updated： Aggregation Period:Jul 16, 2025～Aug 12, 2025
This ranking is based on the number of page views on our site.

nozzle Product List

46～56 item / All 56 items

Displayed results
2-fluid nozzle "Full cone nozzle (small spray / compact) SCBIMJ"

2-fluid nozzle "Full cone nozzle (small spray / compact) SCBIMJ"

Super compact type! A small spray conical nozzle with a wide flow adjustment range.

The "Charging Cone Nozzle (Small Amount Spray / Ultra Compact) SCBIMJ" consists of four parts: nozzle tip, core, cap, and adapter, and is a two-fluid charging cone nozzle that generates a fine mist with an average particle diameter of less than 100μm. It is an internal mixing type that atomizes by mixing compressed air and liquid inside the nozzle. (Compressed air flows in the center of the nozzle, while liquid flows around the outer perimeter in an internal mixing air type.) It is a liquid pressurization type that supplies liquid to the two-fluid nozzle under pressure. 【Features】 ○ Circular spray pattern with uniform flow distribution ○ Minimum spray flow rate among two fluids ○ Ultra-compact shape with a total length of about 42mm ○ ON-OFF control function included ○ Liquid pressurization type that sprays at a pressure of approximately 0.1 to 0.3 MPa For more details, please contact us or download the catalog.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Integrated standard fan-shaped nozzle "Yamagata distribution nozzle VP"

Integrated standard fan-shaped nozzle "Yamagata distribution nozzle VP"

Ceramic nozzle! A simple integrated nozzle that generates a fan-shaped spray.

The "Yamagata Distribution Nozzle VP" can generate a fan-shaped spray with a Y-shaped flow distribution that is strong in the center and gradually weakens towards both ends. When using multiple nozzles in an array, overlapping the patterns at both ends results in an even flow distribution across the entire width. The nozzle body features a ceramic nozzle tip and is a simple integrated nozzle that is directly screwed into the pipe body. A strainer (available only for metal body products) is standard equipment for small flow models and can also be removed. 【Features】 ○ Ceramic is used in the nozzle body’s tip ○ Simple integrated nozzle ○ Strainer is standard equipment for small flow models and can be removed ○ The spray tip is made of ceramic and resin → The ceramic nozzle is molded with a durable engineering plastic For more details, please contact us or download the catalog.

  • Aggregates and crushed stone
  • Water and sewerage pipe fittings
  • Roof and gutter construction

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
2-fluid nozzle "Fan-shaped nozzle (small amount spray / ultra-compact) SCBIMV"

2-fluid nozzle "Fan-shaped nozzle (small amount spray / ultra-compact) SCBIMV"

Super compact type! A small spray fan nozzle with a wide flow adjustment range.

The "Fan-Shaped Nozzle (Small Amount Spray / Ultra Compact) SCBIMV" consists of four components: nozzle tip, core, cap, and adapter, and is a two-fluid fan-shaped nozzle that generates a fine mist with an average particle diameter of less than 100μm. It is an internal mixing type that atomizes by mixing compressed air and liquid inside the nozzle. (Compressed air flows in the center of the nozzle, while liquid flows around the outer circumference in an internal mixing air type.) It is a liquid pressurization type that supplies pressurized liquid to the two-fluid nozzle. 【Features】 ○ Switchable between two spray patterns: uniform & triangular distribution ○ Minimum spray flow rate among two-fluid systems ○ Wide flow adjustment range ○ Ultra compact type with a total length of approximately 42mm ○ Equipped with ON-OFF control function For more details, please contact us or download the catalog.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Air Nozzle "Fan-Shaped Nozzle (Disassemblable) VZ"

Air Nozzle "Fan-Shaped Nozzle (Disassemblable) VZ"

Steam injection is also possible! An air nozzle that accommodates various injection amounts with chip replacement.

The "Fan-Shaped Nozzle (Disassemblable) VZ" is an air nozzle composed of three parts: a spray tip, a cap, and an adapter. Only the worn spray tip can be replaced, while the cap and adapter are compatible with standard fan-shaped nozzles (for liquids) in three sets. It is capable of spraying not only air but also steam. It is used in industries such as steel, machinery, electronics, paper, pulp, printing, food, and transportation. 【Features】 ○ Compressor specification ○ Wide-angle spray (spray angle 90°) covers a large area ○ Various spray volumes can be accommodated by replacing the tip ○ Steam spraying is also possible ○ Disassemblable type, made of metal For more details, please contact us or download the catalog.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Small Flat Air Nozzle for Blowers 'WindJet YBLW'

Small Flat Air Nozzle for Blowers 'WindJet YBLW'

Achieve high impact and high flow rate blowers even at low pressure! Significant energy savings compared to compressor air.

The "WindJet YBLW" is a compact air nozzle for blowers that enables high impact and high flow rates even at low pressure, thanks to its unique structure that allows for efficient air rectification. By switching from compressor air, significant energy savings can be achieved. Additionally, despite its flat and compact shape, it has a discharge width of 53mm, and we also offer headers with nozzles arranged in parallel to accommodate longer lengths. 【Features】 ■ A fault design that allows air to escape even if objects hit the nozzle discharge area ■ Lower power consumption compared to compressor air systems ■ Compatible with long and complex shapes using headers and adjustable hoses *For more details, please refer to the catalog. Feel free to contact us with any inquiries. Spraying Systems, a global brand for spray nozzles, offers nozzles suitable for various applications based on over 90,000 items of proven performance. *For information on spraying nozzles, please download the PDF or contact us.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Three-group standard fan-shaped nozzle "Yamagata distribution nozzle (disassemblable) V"

Three-group standard fan-shaped nozzle "Yamagata distribution nozzle (disassemblable) V"

Ceramic three-group shape! Disassemblable serrated distribution nozzle that generates a fan-shaped spray.

The "Yamagata Distribution Nozzle V" can generate a fan-shaped spray with a Y-shaped flow distribution that is strong in the center and gradually weakens towards both ends. When overlapping the patterns at both ends during multiple nozzle arrangements, the flow distribution becomes uniform across the entire width. This nozzle consists of three parts: a spray chip, a cap, and an adapter, and only the worn spray chip can be replaced. 【Features】 ○ Disassemblable Yamagata distribution nozzle ○ Ceramic used in the spray chip nozzle section ○ Strainer is standard on small flow products and can be removed ○ The cell team consists of ceramic and resin spray chips → The ceramic nozzle is molded with a robust engineering plastic For more details, please contact us or download the catalog.

  • Aggregates and crushed stone
  • Water and sewerage pipe fittings
  • Roof and gutter construction

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Spray nozzle "King Nozzle" TYPE-MY

Spray nozzle "King Nozzle" TYPE-MY

A fine mist with a large flow rate (1L/min) can be obtained at a water pressure of approximately 0.2MPa.

The 【TYPE-MY】 is a metal spray nozzle that can produce a large volume of fine mist at a low pressure of 0.2 to 0.3 MPa (approximately the pressure of tap water). It contains fine mist particles around 10 µm and relatively larger particles of about 250 µm, so it is not a dry mist. However, in outdoor settings where water saturation is not an issue, it provides cooling through latent heat with a large amount of fine mist, as well as cooling effects from the wetting effect. - In gardens and rooftop gardens: It sprays upwards, simultaneously achieving cooling and watering effects in the surrounding atmosphere, as well as visual effects. - On building rooftops: The fine mist and wetting effects cool the surrounding area of the rooftop, allowing for watering and cooling of the rooftop surface, which can reduce the air conditioning load of the building. - In sports fields, golf courses, tennis courts, and outdoor pools: A cool breeze containing droplets can be generated, providing effective measures against heat.

  • Sanitary fixtures
  • Water and sewerage pipe fittings
  • Pool equipment related

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Uniform Sector Nozzle "Uniform Distribution Nozzle VEP"

Uniform Sector Nozzle "Uniform Distribution Nozzle VEP"

Ceramic integrated nozzle! Sector nozzle with uniform flow distribution spray pattern.

The "Uniform Distribution Nozzle VEP" is a uniform fan-shaped nozzle that generates a fan spray with an even flow distribution across the entire spray pattern. The impact force per unit area is uniform. It is an integrated nozzle that uses ceramic in the spray tip. The Seltim is a ceramic-resin spray tip molded from a robust engineering plastic. It is ideal for use in industries such as steel, machinery, electrical and electronics, printing, food, and vehicles and transportation. 【Features】 ○ Generates a fan spray with uniform flow distribution ○ Spray pattern with uniform flow distribution across the entire area ○ Integrated nozzle that uses ceramic in the nozzle tip ○ Uniform impact force per unit area ○ Seltim is a ceramic-resin spray tip For more details, please contact us or download the catalog.

  • Aggregates and crushed stone
  • Water and sewerage pipe fittings
  • Roof and gutter construction

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
2-fluid nozzle "Fan-shaped nozzle (small amount spray) CBIMV"

2-fluid nozzle "Fan-shaped nozzle (small amount spray) CBIMV"

Small spray type! A two-fluid fan-shaped nozzle that generates a fine mist with an average particle diameter of 100μm or less.

The "Fan-Shaped Nozzle (Small Amount Spray) CBIMV" is a mist generation nozzle that can switch between two spray patterns: uniform and triangular distribution. It is a two-fluid fan-shaped nozzle that generates mist with an average particle diameter of less than 100μm. It is a liquid pressurization type that sprays at a pressure of approximately 0.1 to 0.3 MPa. It can produce two patterns: a uniform flow distribution across the entire area and a triangular distribution that is strong in the center and gradually weakens towards the ends, offering a wide range of flow adjustment. 【Features】 ○ Switchable between uniform and triangular distribution, two spray patterns ○ Minimum spray flow in two fluids ○ Compact type ○ Structure resistant to clogging ○ Spray angles of 45°, 80°, and 110° For more details, please contact us or download the catalog.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
2-fluid nozzle "Fan-shaped nozzle (small amount spray) CBIMV.S"

2-fluid nozzle "Fan-shaped nozzle (small amount spray) CBIMV.S"

Small spray type! A two-fluid fan-shaped nozzle that generates a fine mist with an average particle diameter of 30μm or less.

The "Fan-Shaped Nozzle (Small Amount Spray) CBIMV.S" is a space-saving, high-performance nozzle designed compactly from the BIM series of mist generation nozzles. It is a two-fluid fan-shaped nozzle that generates a fine mist with an average particle diameter of 30μm or less. It is a suction type that does not require a liquid pressurization device, as it uses compressed air to draw up the liquid and spray it. The two-fluid nozzle consists of four parts: a nozzle tip, core, cap, and adapter, providing an even flow distribution across the entire area. 【Features】 ○ Two-fluid fan-shaped nozzle that generates a fine mist with an average particle diameter of 30μm or less ○ Even spray pattern with uniform flow across the entire area ○ No device required for liquid pressurization ○ Compact type ○ Spray angle of 80° For more details, please contact us or download the catalog.

  • Water and sewerage pipe fittings

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Uniform Sector Nozzle "Uniform Distribution Nozzle VE"

Uniform Sector Nozzle "Uniform Distribution Nozzle VE"

Replaceable nozzle! Sector-shaped nozzle that generates a uniform flow distribution in a fan-shaped spray.

The "Uniform Distribution Nozzle VE" is a uniform sector nozzle that generates a fan-shaped spray with an even flow distribution across the entire spray pattern. The impact force per unit area is uniform. It is a three-part nozzle that uses ceramic in the spray tip nozzle section. It consists of a spray tip, cap, and adapter, allowing for the replacement of only the worn spray tip. The strainer is standard equipment for small spray volume products and is removable. 【Features】 ○ Generates a fan-shaped spray with an even flow distribution ○ Spray pattern with uniform flow distribution across the entire area ○ Replaceable nozzle section when worn ○ Uniform impact force per unit area ○ Strainer is standard equipment for small spray volume products and is removable For more details, please contact us or download the catalog.

  • Aggregates and crushed stone
  • Water and sewerage pipe fittings
  • Roof and gutter construction

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Search Keywords Related to nozzle

COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.