Last Updated： Aggregation Period:Sep 10, 2025～Oct 07, 2025
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:Sep 10, 2025～Oct 07, 2025
This ranking is based on the number of page views on our site.
Last Updated： Aggregation Period:Sep 10, 2025～Oct 07, 2025
This ranking is based on the number of page views on our site.
766～780 item / All 927 items
Area Setting Remote Control TS-A
■Main Features ●The area setting remote control is specifically designed for the toilet sensor "TS-7 series." ●It can be used universally with all toilet sensors in the "TS-7 series." ●By pressing the buttons on the remote control, you can reset the area of the toilet sensor.
This is a sensor dedicated to the Living Safety Notification System, which adds a time function to the human movement sensor for enhanced living safety notifications!
■Living Safety Sensor This is a dedicated sensor for the 'Living Safety Notification System,' which integrates a "human movement sensor" with the time function of a "living safety notifier." It detects human movement using a passive sensor, and if no movement is detected within a pre-set timer duration, it alerts to a change in living rhythm. The timer can be set to 15 different durations (20 seconds, 5 minutes, 1, 6, 8, 9, 10, 11, 12, 13, 15, 16, 18, 22, and 24 hours). ■Two Types: Surface-Mounted and Recessed It is installed on the ceiling surface of corridors and living spaces used in daily life. With a sophisticated design reminiscent of downlights, both the surface-mounted and recessed types do not compromise architectural beauty. ■User-Friendly Design To eliminate the relay operation sound during detection, a photoMOS relay has been adopted. This allows for a quiet living environment without worrying about the sensor's operational noise. The detection indicator light also uses a gentle green color that is easy on the eyes. ■Pre-Notification Function If no human movement is detected within the set time, a pre-notification output occurs 5 minutes in advance. By connecting a buzzer or light, the system can be effectively utilized.
This is a sensor dedicated to the Living Safety Notification System, which adds a time function to the human movement sensor for enhanced living safety notifications!
■Living Safety Sensor This is a dedicated sensor for the 'Living Safety Notification System,' which integrates a "human movement sensor" with the time function of a "living safety notifier." It detects human movement using a passive sensor, and if no movement is detected within the pre-set timer duration, it alerts to a change in living rhythm. The timer can be set to 15 different durations (20 seconds, 5 minutes, 1, 6, 8, 9, 10, 11, 12, 13, 15, 16, 18, 22, and 24 hours). ■Two Types: Surface-Mounted and Recessed It is installed on the ceiling surfaces of hallways and living rooms used in daily life. With an elegant design reminiscent of downlights, both the surface-mounted and recessed types do not compromise architectural beauty. ■User-Friendly Design To eliminate the relay operation sound during detection, a photoMOS relay has been adopted. This allows for a quiet living environment without worrying about the sensor's operational noise. The detection indicator light also uses a gentle green color for the eyes. ■Pre-Notification Function If no human movement is detected within the set time, a pre-notification output will occur 5 minutes in advance. By connecting a buzzer or light, the system can be effectively utilized.
一人住いや個室で生活される方の、安心システムです。 人の動きセンサーと接続して、動作しない時間を検知してお知らせします。
■主な特長 ●DC12V、DC24V、AC100Vで使用できる3電源方式です。 ●タイマー出力と事前報知出力を装備しています。 ●出力は保持モード、3秒モードの切り替えができます。 ●4種類のLEDで検知(緑)、報知(赤)、メモリー(赤)の状態を表示します。 ●設定時間を満了しても報知遅延機能を生かし5分間メロディーでお知らせします。 ●報知音の音色は2種類で音量は0～80dBの可変式です。 ●センサー信号入力はa接点です。 ■生活安心報知 ●人の動きセンサーを日常生活でよく使う場所に設置して接続します。 ●タイマー設定時間を経過しても、センサーが人を検知しない場合、どこかで倒れていると判断して、チャイム音と表示灯でお知らせします。 ●一人住まいの方の場合、外部出力により緊急通報装置を起動させ、近親者宅などへ通報します。 ●入力に対する時間は2台(生活1、生活2)それぞれ設定可能です。 ●万が一、1台が誤動作しても安全側に働くよう2台接続できます。 ■ナースコールシステムに接続 ●DC24Vでも使用できるので、施設のナースコールシステムに組み込めます。
It connects to a toilet sensor and notifies you of two types of time: continuous use of the toilet or when it is not in use (lifestyle detection).
■Main Features ● It is a three-power supply system that can be used with DC12V, DC24V, and AC100V. ● It is equipped with timer output and pre-notification output. ● The output can switch between hold mode and 3-second mode. ● The status of detection (green), notification (red), and memory (red) is displayed with four types of LEDs. ● Even after the set time expires, it utilizes the notification delay function to inform with a melody for 5 minutes. ● There are two types of notification sounds, and the volume is adjustable from 0 to 80dB. ● The sensor signal input is a contact point. ■ Toilet Safety Notification ● It connects to the toilet sensor TS-7 series. ● The sensor detects when a person enters the toilet. ● It notifies the continuous usage time of the toilet (e.g., 10 minutes, 15 minutes) and the time when the toilet is not used (e.g., 8 hours, 9 hours). ● A real-time output is provided for connecting a display light. ■ Connection to Nurse Call System ● It can also be used with DC24V, allowing it to be integrated into the facility's nurse call system. ● It can be used to notify when a patient has been bedridden for longer than the set time or when they have not gotten into bed.
We adopted a light beam method that is not affected by temperature changes. It detects distances using a new method, capable of sensing heights above 60 cm from the floor.
■Overview ● Used in the Life Safety Notification System. ● Connects to life safety notification devices, and will notify if the sensor does not detect for a set period of time. ■Features ● Since it uses a light beam to measure distance, it does not react to temperature changes such as heating, cooling, sunlight, or drafts. ● If the area changes continuously for more than 30 minutes, such as when items are placed, it automatically adjusts the detection height independently for each beam. ● With a standard ceiling height of 2.5m, it can detect up to a height of 1.9m, so it will not detect pets, small animals, or robotic vacuum cleaners. ■Main Specifications ● A total of 7 beams can be adjusted in three stages: 0°, 3°, and 6°. ● The areas at both ends can be set in three patterns: +0.2m/active/inactive. ● The green LED display can be set to either always off or off during detection. Installation ● Suitable for the rooms of elderly residents living alone in senior housing. ● Available in two types: "exposed type" for easy installation and "embedded type" that matches the installation location.
This is a multifunction display panel for the life safety notification system.
■Features 1. Channel display panel function (immediately notifies and outputs when there is a contact input) 2. Life safety notification function (notifies and outputs when the set time exceeds) 3. Life sensor display panel function (connects to sensors with remote input function, and ON/OFF for each channel is linked to remote output. There is no individual output) Three functions are provided. ■Control each room with the main unit No need for an occupancy confirmation switch or card holder switch; control can be done with the main unit. ■Individual channel input Each channel can be operated with an ON/OFF switch, allowing operation only in the necessary rooms when needed. ■Signal input displayed with chime and LED When a signal is input from connected devices, a chime sound and LED display will occur, allowing the operational status of the connected devices to be confirmed visually and audibly.
This is a multifunctional display panel for the life safety notification system.
■Features 1. Channel display panel function (immediately notifies and outputs when there is a contact input) 2. Life safety notification function (notifies and outputs when the set time exceeds) 3. Life sensor display panel function (connects to sensors with remote input function, and ON/OFF for each channel is linked to remote output. There is no individual output) Three functions are provided. ■Control each room with the main unit No need for an occupancy confirmation switch or card holder switch; control can be done with the main unit. ■Individual channel input Each channel can be operated with an ON/OFF switch, allowing operation only in the necessary rooms when needed. ■Signal input displayed with chime and LED When a signal is input from connected devices, a chime sound and LED display occur, allowing the operational status of connected devices to be confirmed visually and audibly.
This is a 4-channel display board that notifies with a flash and melody (chime).
■ Signal input is notified by flashlight and melody (chime) When a signal is input from a connected device, it will notify you with a flashlight and melody (chime). You can register alert sounds and set ON/OFF for each channel. ■ Output and display mode switching function You can switch between 'hold mode', which continuously outputs until the stop button on the main unit is pressed, and modes of 3 seconds, 6 seconds, 15 seconds, or 30 seconds, allowing for settings according to the system. ■ Chime and melody sounds selectable from various options There are 10 types of alert sounds combined with melodies, which can be registered arbitrarily from 1CH to 4CH. The alert (red LED blinking) will sound in conjunction. It will not sound when the volume is set to OFF.
A display panel that shows the signal input from 5 systems with melodies (chimes) and flashes, capable of communicating with up to 4 locations.
■ Signal input is indicated by a flashlight and melody (chime). When a signal is input from the connected device, it will be indicated by a chime sound and LED, allowing you to confirm the operational status of the connected device visually and audibly. (a contact and b contact inputs can be selected) - Alert sound: Refer to the alert sound list (can be set for each channel) ■ 5-channel individual input Each channel is equipped with an ON/OFF switch, allowing operation only in necessary locations at necessary times. ■ LED display hold/non-hold The LED can display various indications based on settings. OFF: off / Standby: green light / Input: red blinking In short-time mode, the LED can be set to hold or non-hold. ■ Output/display mode switching function You can switch between 'hold mode', which continuously outputs until the main unit's stop button is pressed, and 'short-time mode', which automatically propagates (3 seconds, 150 seconds, 30 seconds), allowing settings according to the system. ■ Check function When there is an input in the reset state, it will turn red in conjunction, allowing for loop checking. (This is the same in the case of communication connection)
Signal input from 10 systems displayed with melody (chime) and flash, with a display panel that can connect up to 4 locations.
■ Signal input is notified by flashlight and melody (chime). The channel display panel shows the input signal from the connected device with chime sounds and LED indicators, allowing for immediate confirmation of the operational status of the connected device. ● Alert sound: Refer to the alert sound list (configurable for each channel) ● LED display: OFF: Off, Standby: Green light, Input: Red blinking ■ In short-time mode, the LED can be set to either hold or non-hold. ■ Output and display mode switching function You can switch between 'hold mode', which continuously outputs until the stop button on the main unit is pressed, and 'short-time mode' (3 seconds, 15 seconds, 30 seconds), allowing for settings tailored to the system. ■ 10-channel individual input Each channel is equipped with an ON/OFF switch, enabling operation of only the necessary channels when needed. ■ Remote input terminal The operation stops with a make input. The display for each channel and set/reset will turn off. ■ External power supply Provides external power of DC 12V, 400mA when supplied with AC 100V.
Existing pole-mounted sensors can easily be converted to housing type.
■Compact Housing Type This is a compact housing type that is easy to install, allowing for simple attachment and excellent design aesthetics. ■Outstanding Security Due to its structure that conceals the interior, the position of the sensor's warning line and the types of sensors installed cannot be identified, providing superior security. ■Easy Installation Installation is straightforward as it simply involves covering the pole (specific to KP-100/100B), making it easy to set up. ■Retrofit Installation on Existing Poles It is easy to retrofit onto existing pole installations. Additionally, it supports back-to-back installation of sensors. *For new installations, a pole is required. Beam direction: within 140° ■Compatible Models - PXB-HFA series - PXB-F series - PXB-100SW - PXB-TE series - PB-TE series - PB-FZ series - PB-F series - PB-IN-HF series - PB-IN-100AT - BUS-XF series - BUS-XT series *Please attach the included lock spacer to the sensor for use.
An infrared sensor storage case that excels in aesthetics and can be installed anywhere.
■ Discreet vigilance is possible By adopting invisible colored acrylic pipes inside and placing the entire frame on the inside, the installation position and direction of the sensors are not discernible. ■ Strong design with excellent durability It is resistant to impact and has outstanding durability, allowing for long-term use. The material primarily consists of galvanized and painted steel plates, with stainless steel used for bolts. ■ Customizable vigilance network Single beam, double beam, and four-stage beam infrared sensors can be used, allowing for linear and loop vigilance. Additionally, the height at which the sensors are installed can be adjusted, enabling the optimal configuration of the vigilance network according to the installation location. ■ Capable of accommodating specifications beyond standard By modularizing the internal structure of the housing, it is designed to also accommodate microwave sensors, solar cell units, and more. ■ Compatible models - PXB-HF-KH series - PXB-HFA series - PXB-F series - PXB-TE series - PXB-100SW - BUS-XF series - BUS-XT series - PB-IN-HF series - PB-FZ series - PB-IN-100AT
An infrared sensor storage case that excels in aesthetics and can be installed anywhere.
■ Discreet vigilance is possible By adopting invisible colored acrylic pipes inside and placing the entire frame on the inside, the installation position and direction of the sensors are not discernible. ■ Strong design with excellent durability It is resistant to impact and has outstanding durability, allowing for long-term use. The material mainly consists of galvanized and painted steel plates, with stainless steel used for bolts. ■ Customizable vigilance network Single beam, double beam, and four-stage beam infrared sensors can be used, allowing for linear and loop vigilance. Additionally, the height of the sensor installation can be adjusted, enabling the optimal configuration of the vigilance network according to the installation location. ■ Capable of accommodating specifications beyond standard By modularizing the internal structure of the housing, it is designed to also accommodate microwave sensors, solar cell units, and more. ■ Compatible models - PXB-HF-KH series - PXB-HFA series - PXB-F series - PXB-TE series - PXB-100SW - BUS-XF series - BUS-XT series
Housing Case KH-70ST
For more details, please refer to the basic information.
