Railway Technology Exhibition 2019 Exhibition Information Komaihaltec

Technical materials featuring construction achievements are being distributed. A reduction of approximately 79% in process time is possible compared to conventional methods!

The "R Anchor" is a post-installed anchor bolt that can be removed after use, such as for temporary materials. It uses acrylic resin instead of conventional epoxy resin as the adhesive for the anchor bolt. Acrylic resin has the following features: - Can be installed at low temperatures down to -10°C - Short curing time (Summer resin: approximately 70 minutes at 25°C, Winter resin: approximately 120 minutes at 5°C) - Can be applied to wet surfaces Additionally, during installation, it eliminates the need for the setup and removal of pipes and sealing materials, as well as resin measurement and mixing tasks, allowing for approximately 79% reduction in process time compared to conventional methods. ★ Technical materials containing construction achievements are available upon request ★ [Contents (excerpt)] - About acrylic resin - Performance verification tests - Construction achievements [Applicable examples] - Temporary equipment during bridge construction (preventing overturning and falling during girder installation, etc.) - Fixing brackets for jack-up during bearing replacement - General civil engineering work, construction work, factory equipment fixation, etc. *For more details, please refer to the catalog or feel free to contact us.

• Bridge Materials
• Bridge Construction
• Other earthworks, foundation works, and exterior floors

This is a list of "NR Anchors" and "R Anchors" that can be installed even at low temperatures of -10℃.

The "NR Anchor" is an anchor bolt that uses acrylic resin and is applicable to all post-installed anchor bolts used in concrete structures. It has high viscosity and a short curing time, allowing for a reduction in process time. During injection, there is no need for the installation and removal of pipes or seal materials, nor for resin measurement and mixing work. 【Features】 ■ Can be installed at low temperatures (minimum usable temperature -10°C) ■ Minimal strength reduction even with rough mixing ratios of the two components ■ Prevents construction defects such as mixing errors ■ Short curing time The "R Anchor" is a post-installed anchor bolt that can be removed after use, such as for temporary materials. It has a special coating on the embedded part of the anchor bolt, allowing it to be removed by applying reverse rotation with a wrench after use. 【Features】 ■ Can be removed by rotating the bolt in reverse. ■ No need for concrete chipping or cutting of the anchor bolt during removal ■ Noise reduction ■ Can be installed at low temperatures (minimum usable temperature -10°C) *For more detailed information, please contact the manufacturer of the R Anchor, Sanpo Co., Ltd.!

• Bridge Materials
• Bridge Construction
• Railway Construction

Environmentally friendly and structure-friendly! Concrete surface protection material using acrylic rubber.

The "Alonbur Coat Z-X and Z-Y Method" is a concrete surface protection material that uses acrylic rubber. Repair methods for concrete structures that utilize the features of "Alonbur Coat" include the Z-X method (prevention of deterioration + prevention of peeling) and the Z-Y method (prevention of deterioration). All standard materials used are water-based, resulting in minimal organic solvent odors or unpleasant smells, as well as reduced skin irritation commonly associated with organic materials, making it environmentally friendly for both the surrounding area and workers. The coating can be reapplied, which is effective for environmental measures and waste reduction during the next repainting. 【Features】 ■ Environmentally friendly due to the use of water-based materials ■ Repainting of the coating is possible ■ Allows moisture release from within the concrete ■ Good adhesion durability of the membrane layer to the concrete ■ Easy maintenance *For more details, please refer to the catalog or feel free to contact us.

• Other civil engineering works
• Concrete construction
• Renovation and repair methods

Sekisui Filler Co., Ltd. will be exhibiting at the "Automotive Technology Exhibition 2026 YOKOHAMA" held at PACIFICO YOKOHAMA from May 27. (Booth number 285, within the Sekisui Chemical booth) 【Exhibited Products】 Mobility G - Re-sealable gasket HM (EV Seal 500) - Interior materials (Thermonex/Swiftlock) - Battery protection materials (EV Protect 4006SFR, etc.) Electronics / Car Electronics - Adhesives for camera modules - Adhesives for displays - Conformal coating agents - Optical adhesives We sincerely look forward to your visit.

Palmholtz Co., Ltd. will be exhibiting at the "AXIA EXPO 2026" held at Aichi Sky Expo (Aichi Prefectural International Exhibition Center). Our company possesses unique new technologies that transform oil palm trunks (Oil Palm Trunk = OPT), which have been treated as unused resources due to their lack of strength and value as building materials, into wood-based products such as building materials and furniture. The oil palm, which produces a large amount of edible oil, leaves the trunks unused and discarded after the oil is extracted. It is estimated that the amount of discarded trunks is 20 million tons per year in both Malaysia and Indonesia. This project involves peeling and drying the unused oil palm trunks to create veneer, which is then layered and compressed under high temperature and pressure to manufacture and sell exterior materials. We showcased a bench as a reference exhibit at the Malaysia Pavilion during the 2025 Osaka Expo. We sincerely look forward to your visit.

Kawasaki Corporation (Headquarters: Tokyo) is pleased to announce that it will participate in the interim report meeting for the Tokyo Metropolitan Government's "Decarbonization Support Project in the Supply Chain for the Creation of a Green Products Market," which will be held on May 20, 2026. At this meeting, we will present the CO2 reduction effects of our environmentally friendly plastic formwork "Daiko Panel," which we have conceived, developed, manufactured, and sold, along with our initiatives towards greening, including related auxiliary materials. [Overview of the Presentation] Theme: Utilizing CFP to enhance CO2 reduction of "Daiko Panel" and promote greening throughout the entire supply chain. Main Content: Introducing initiatives aimed at CO2 reduction, referencing the background of our application for this project and the CFP calculation results for "Daiko Panel" and its auxiliary materials. [Presentation Date and Time] Interim report meeting: May 20, 2026 (Wednesday) from 15:00 to 17:00 Details of the interim report meeting and the Tokyo Metropolitan Government's project: Decarbonization support in the supply chain for the creation of a green products market https://www.cfp-sc.metro.tokyo.lg.jp/

Rentama Co., Ltd. will be exhibiting at the "8th International Construction and Surveying Exhibition (CSPI2026)" held at Makuhari Messe. A wide range of cutting-edge products, technologies, and services from the evolving industries of construction machinery, heavy equipment, attachments, construction DX, and i-Construction will be gathered in one place. This is one of the largest exhibitions in Japan for professionals in the construction and surveying industries to gather for business discussions, advanced information gathering, and problem-solving. This is a valuable opportunity to see KEMROC products up close. We understand you may be busy, but we invite you to stop by our booth. We look forward to meeting everyone.

TESSHA Corporation will be exhibiting at 'FOOMA JAPAN 2026' held at Tokyo Big Sight. This exhibition covers various fields of food manufacturing and is one of the largest comprehensive food manufacturing exhibitions in the world, where advanced technologies and knowledge come together. We plan to showcase our "Small Catalytic Deodorization Device SCU-1EH type." We look forward to your visit.