Railway Technology Exhibition 2019 Exhibition Information Komaihaltec

Technical materials featuring construction achievements are being distributed. A reduction of approximately 79% in process time is possible compared to conventional methods!

The "R Anchor" is a post-installed anchor bolt that can be removed after use, such as for temporary materials. It uses acrylic resin instead of conventional epoxy resin as the adhesive for the anchor bolt. Acrylic resin has the following features: - Can be installed at low temperatures down to -10°C - Short curing time (Summer resin: approximately 70 minutes at 25°C, Winter resin: approximately 120 minutes at 5°C) - Can be applied to wet surfaces Additionally, during installation, it eliminates the need for the setup and removal of pipes and sealing materials, as well as resin measurement and mixing tasks, allowing for approximately 79% reduction in process time compared to conventional methods. ★ Technical materials containing construction achievements are available upon request ★ [Contents (excerpt)] - About acrylic resin - Performance verification tests - Construction achievements [Applicable examples] - Temporary equipment during bridge construction (preventing overturning and falling during girder installation, etc.) - Fixing brackets for jack-up during bearing replacement - General civil engineering work, construction work, factory equipment fixation, etc. *For more details, please refer to the catalog or feel free to contact us.

• Bridge Materials
• Bridge Construction
• Other earthworks, foundation works, and exterior floors

This is a list of "NR Anchors" and "R Anchors" that can be installed even at low temperatures of -10℃.

The "NR Anchor" is an anchor bolt that uses acrylic resin and is applicable to all post-installed anchor bolts used in concrete structures. It has high viscosity and a short curing time, allowing for a reduction in process time. During injection, there is no need for the installation and removal of pipes or seal materials, nor for resin measurement and mixing work. 【Features】 ■ Can be installed at low temperatures (minimum usable temperature -10°C) ■ Minimal strength reduction even with rough mixing ratios of the two components ■ Prevents construction defects such as mixing errors ■ Short curing time The "R Anchor" is a post-installed anchor bolt that can be removed after use, such as for temporary materials. It has a special coating on the embedded part of the anchor bolt, allowing it to be removed by applying reverse rotation with a wrench after use. 【Features】 ■ Can be removed by rotating the bolt in reverse. ■ No need for concrete chipping or cutting of the anchor bolt during removal ■ Noise reduction ■ Can be installed at low temperatures (minimum usable temperature -10°C) *For more detailed information, please contact the manufacturer of the R Anchor, Sanpo Co., Ltd.!

• Bridge Materials
• Bridge Construction
• Railway Construction

Environmentally friendly and structure-friendly! Concrete surface protection material using acrylic rubber.

The "Alonbur Coat Z-X and Z-Y Method" is a concrete surface protection material that uses acrylic rubber. Repair methods for concrete structures that utilize the features of "Alonbur Coat" include the Z-X method (prevention of deterioration + prevention of peeling) and the Z-Y method (prevention of deterioration). All standard materials used are water-based, resulting in minimal organic solvent odors or unpleasant smells, as well as reduced skin irritation commonly associated with organic materials, making it environmentally friendly for both the surrounding area and workers. The coating can be reapplied, which is effective for environmental measures and waste reduction during the next repainting. 【Features】 ■ Environmentally friendly due to the use of water-based materials ■ Repainting of the coating is possible ■ Allows moisture release from within the concrete ■ Good adhesion durability of the membrane layer to the concrete ■ Easy maintenance *For more details, please refer to the catalog or feel free to contact us.

• Other civil engineering works
• Concrete construction
• Renovation and repair methods

Nitto Kohki will hold the "2025 Attack Fair in Meiko" for two days from July 23 (Wednesday) to July 24 (Thursday), 2025, at the "Kowa Seminar Plaza 2F Training Room No. 12 (inside Kowa Sports Land)." The Attack Fair is an exhibition where you can actually "see, touch, and operate" Nitto Kohki's products. Additionally, there will be wonderful souvenirs for attendees and many fun activities prepared. We look forward to welcoming everyone!

We will be exhibiting at the "62nd JAPAN DIY HOMECENTER SHOW 2026." This year, the largest exhibition in the industry will be held with the theme "Let's Go to the DIY Festival in Summer!" Please be sure to visit our booth (No. M31). ■ Introduction of Exhibited Product: Insulation Material "SS Premier" We are introducing "SS Premier" with the concept of moving away from the existing 20mm thick insulation materials. [The secret of 5mm. Maintaining performance while being overwhelmingly thin, light, and easy to install.] - Achieves insulation performance equivalent to RW50mm with a thickness of just 5mm, making it possible to install in limited spaces. - As a sheet material, it can accommodate both round and square ducts. - Lightweight and flexible, making transportation and handling easy, reducing the burden on the job site. Compared to conventional products, it offers advantages in installation space, transportability, and retail display. It has numerous implementation records across the country, including government projects such as the Shibuya Ward Office reconstruction project, as well as universities, hospitals, and large-scale new construction projects. At the venue, you can take a look at actual product samples. All of our staff are sincerely looking forward to your visit at booth No. M31.

Kou Alpha X Co., Ltd. will be exhibiting at the "Automatic Identification Comprehensive Exhibition" held at Tokyo Big Sight. At our booth, we will showcase a wide range of products, including metal-compatible RFID tags (PMT series), "keychain-type tags," and "rugged, environment-resistant tube tags." We look forward to your visit.

North Engineering, the Taiwanese agent of Tokkyo Kiki Co., Ltd., will exhibit at the international exhibition "SEMICON TAIWAN 2026" held in Taiwan. At "SEMICON Taiwan," we will showcase products for micro-vibration and magnetic field countermeasures for semiconductor manufacturing plants, as well as seismic isolation devices for transformers and vibration-damping devices for air conditioning outdoor units as earthquake countermeasures. Event Dates: September 2 (Wednesday) - September 4 (Friday), 2026 Venue: Taipei Nangang Exhibition Center (TaiNEX Hall 1 & 2, Taipei City, Taiwan) Booth Number: K2568 (TaiNEX 1, 1st Floor)

"I don't have anyone in the company to ask if this is the right way to segment." "I can't decide whether it's okay to delete the scenarios set up by my predecessor." I often hear such voices from those in charge of operating MA tools. In this seminar, Shannon, as an MA vendor, will publicly share how they operate MA within their own marketing department, using the actual management screen. Please note that this seminar will not be recorded or archived. It will be presented only to the 15 companies that attend in person. [Screens to be viewed on the day] (tentative) 1: Conditions for segmentation 2: Flow and branches of scenarios 3: Discarded settings [Recommended for those who] - Are almost solely responsible for operating MA tools - Have not been able to make changes to the settings inherited from their predecessor - Feel that they are not using MA as they had originally intended - Want to know how other companies are actually operating at the screen level - Are considering reviewing their current MA tools