The most recommended and ideal data destruction device right now is the physical destruction device, Storage Puncher STPN-30.

A manual device capable of physically destroying HDDs with 6 tons of hydraulic power and 4 destruction bits. By replacing the destruction tool, it can also destroy SSDs and magnetic tapes.

1. Simple operation by just inserting the HDD into the main unit and moving the handle up and down by hand. 2. Destructive power of up to 6 tons. 3. HDD destruction is possible with high hydraulic power. 4. Creates four holes in the HDD and destroys the HDD platter in a single destruction cycle. 5. By exchanging various destruction tools on a single main unit, physical destruction of SSDs and magnetic tapes is also possible (world's first). 6. Even if the destruction bit (pin) is damaged or worn, the tip bit can be easily replaced, allowing for continued work with peace of mind. 7. Unique feature that prevents the destruction shaft from becoming stuck after destruction. 8. Battery operation is possible even in places without power, enabling on-site destruction work (world's first).

• Entrance and exit control system
• Security Assessment

A data erasure device for HDD, SSD, and SAS that can erase at a rate of 18GB per minute while keeping the mount attached, with no license fees and no internet connection required.

SAS, SSD, SAS data erasure device Jet Eraser 8-port model HDE-GT series HDE-GT800. 1. Over 30GB per minute ultra-fast data erasure, 2. Data erasure for SAS, SSD, and HDD, 3. All ports are independent and asynchronous, allowing for efficient work as drives with faster speeds or smaller capacities can be swapped out when finished, 4. Ability to terminate operations on faulty drives midway, 5. No need to remove the mount, 6. Erasure modes: Quick Erase, Full Erase, DoD Erase, DoD Erase with Compare, Seven Pass Erase, Secure Erase, NSA Erase, 7. Log saving capability, 8. PC link function, 9. A wide range of optional adapters to support various interfaces.

• others
• Security Assessment
• Firewall

No license fee required, no internet connection needed, can be used with the mount attached, and can leave a deletion log; 18GB per minute HDD, SSD, and SAS data erasure device.

SAS, SSD, SAS data erasure device Jet Eraser HDE-GT400 4-port model. 1. Over 30GB per minute ultra-fast data erasure, 2. Data erasure for SAS, SSD, and HDD, 3. All ports are independent and asynchronous, allowing for efficient operation as the next drive can be swapped in when a faster HDD or a smaller capacity HDD finishes first, 4. Ability to terminate the operation of faulty drives midway, 5. No need to remove the mount, 6. Erasure modes: Quick Erase, Full Erase, DoD Erase, DoD Erase with Compare, Seven Pass Erase, Secure Erase, NSA Erase, 7. Log saving capability, 8. PC link function, 9. A wide range of adapter options to support various interfaces.

• Other security systems
• others
• Firewall

USB duplicator equipped with a CD-ROM function that prevents data tampering, deletion, and formatting using a dedicated USB, allowing for data protection.

The U-Reach C series USB duplicator offers optimal models ranging from 1:9 to 1:119 based on the number of slots. It can write at a speed of 2.0GB per minute. CD-ROM creation involves write protection to prevent data tampering, deletion, and formatting, resulting in Read-Only Memory (ROM). When this memory is inserted into a PC, it is recognized as a CD-ROM rather than a USB memory, allowing for automatic autorun. It is ideal for movies, music, and content. Traditionally, USB data lacked protection, making it prone to easy deletion, tampering, and formatting, which caused issues for distribution. A dedicated USB memory is required. Furthermore, with this duplicator, it is possible to erase CD-ROM created content and write new data multiple times. Overall, it allows for the selection of protection for each partition.

• others
• Security Assessment
• Firewall

No license fee required, no internet connection needed, can be used with the mount attached, capable of high-speed erasure at 18GB per minute while leaving a deletion log, HDD and SSD erasure device.

Our company has planned and developed the groundbreaking data erasure device MTS-SAS for SAS, SSD, and SATA. 1. Over 18GB per minute ultra-fast data erasure, 2. Supports SAS, SSD, and HDD, 3. All ports are independent and asynchronous, allowing for efficient work as drives with faster speeds or smaller capacities can be swapped out once they finish, 4. Ability to terminate operations on defective drives midway, 5. No need to remove the mount, 6. Erasure modes: Quick Erase, Full Erase, DoD Erase, DoD Erase with Compare, Seven Pass Erase, Secure Erase, NSA Erase, 7. Log saving capability, 8. PC link function, 9. A wide range of optional adapters to support various interfaces.

• others
• Firewall

An electric device that physically destroys HDDs with 12 tons of hydraulic power and 4 destruction bits. By swapping the destruction tool, it is also possible to destroy SSDs and magnetic tapes.

1. Simple operation that allows physical destruction by simply inserting the recording medium into the main unit and pressing the start button. 2. Destruction power of up to 12 tons. 3. Utilizes hydraulic power, enabling high-power destruction of HDDs. 4. With just one main unit, various destruction tools can be exchanged to enable physical destruction of SSDs and magnetic tapes (world's first). 5. Creates four holes in the HDD during a single destruction process, destroying the recording surface platter. 6. Even if the destruction bit (pin) is damaged or worn, it can be easily replaced, allowing for continued work with peace of mind. 7. Unique feature that prevents the destruction shaft from becoming dislodged after destruction. 8. Capable of battery operation in locations without power, enabling on-site destruction work (world's first).

• Security Assessment
• Firewall

With 12 tons of hydraulic power, it can physically destroy HDDs and SSDs, and even if the cutting bits are damaged or worn, they can be easily replaced. It is also capable of destroying magnetic tapes.

1. Simple operation by just inserting the recording medium into the main unit and pressing the start button. 2. Destructive power of up to 12 tons. 3. Uses hydraulic power, enabling the destruction of HDDs and SSDs with high power. 4. With just one main unit, various destruction tools can be exchanged to physically destroy HDDs, SSDs, and magnetic tapes (world's first). 5. SSDs are bent to physically destroy the internal semiconductor IC chips. 6. Even if the destruction bit at the tip is damaged or worn, it can be easily replaced, allowing for continued work with peace of mind. 7. Can be battery-operated in locations without power, enabling on-site destruction work (world's first).

• Other security systems
• Security Assessment
• Firewall

An electric physical destruction device that cuts LTO and other magnetic tapes with 12 tons of hydraulic power and cutting blades. By replacing the destruction tool, it is also possible to destroy HDDs and SSDs.

1. Simple operation by just inserting the recording medium into the main unit and pressing the start button. 2. Destructive power of up to 12 tons. 3. Uses hydraulic power, enabling high-power magnetic tape cutting. 4. By exchanging various destruction tools on a single main unit, physical destruction of HDDs and SSDs is also possible (world's first). 5. Even if the cutting and destruction blade is damaged or worn, it can be easily replaced, allowing for continuous work with peace of mind at any time. 6. Battery operation is possible even in places without power, enabling on-site destruction work (world's first).

• Security Assessment
• Firewall

An electric destruction device capable of physically destroying HDDs and SSDs with 12 tons of hydraulic power. By simply changing the tool, it can also destroy magnetic tapes with one machine.

1. Simple operation that allows for physical destruction by just inserting the recording medium into the main unit and pressing the start button. 2. Destructive power of up to 12 tons. 3. Uses hydraulic power, enabling high-power destruction of HDDs and SSDs. 4. Creates four holes in an HDD and bends an SSD for physical destruction in a single operation. 5. With just a tool exchange on the main unit, physical destruction of magnetic tapes is also possible (world's first). 6. Even if the destruction bit at the tip is damaged or worn, it can be easily replaced, allowing for continued work with peace of mind. 7. Unique feature that prevents the HDD destruction shaft from becoming stuck after destruction. 8. Battery operation is possible even in locations without power, enabling onsite destruction work (world's first).

• Other security systems
• others
• Security Assessment

SSD Shredder Flash EX completely prevents information leakage by crushing SSDs and smartphone IC chips into extremely small pieces.

The SSDs equipped with a large amount of flash memory and smartphones require physical destruction of the IC chip to completely erase data, but it is possible to completely prevent information leakage by shredding them. Flash EX is a highly reliable compact SSD shredder that meets very strict standards worldwide. The items to be shredded include SSDs, smartphones, USB memory, SD cards, CDs/DVDs, and credit cards, with shredding resulting in particles as small as 4 x 15 mm. The shredder has a control panel on the top, making it easy to use. Additionally, there is a window in the media feed slot that allows users to check the shredding status, providing peace of mind. In data centers, there is a shift to high-speed, long-lasting, and energy-efficient SSDs for server storage, and shredding is always required when replacing these SSDs, making this shredder essential. Support for Windows 10 will end on October 14, 2025, leading to a predicted increase in demand for computer replacements, necessitating the destruction of SSDs for laptops. The SSD shredder Flash EX will also be indispensable for data erasure and destruction service companies, as well as mobile data erasure and destruction service providers.

• others
• Firewall

Kort Valuta Inc. (Head Office: Shibuya, Tokyo; CEO: Hideki Shibata, hereinafter “the Company”) provides TwooCa, a next-generation wallet that combines employee/member benefit features such as point rewards with digital payments and digital money utilization. We are pleased to announce the official release of TwooCa Mall, a closed online mall exclusively available to employees and members of companies that have implemented TwooCa. In conjunction with the official launch, we have also released a dedicated landing page that consolidates information for prospective partner merchants. This page clearly outlines the benefits and features for companies considering joining the TwooCa Mall platform. Press Release: https://prtimes.jp/main/html/rd/p/000000082.000076589.html

Japan is one of the top 10 countries in the world with frequent earthquakes. The 2020 White Paper on Land, Infrastructure, Transport and Tourism has also reported an increase in the probability of major earthquakes occurring. Regarding the Nankai Trough earthquake, the probability of an earthquake with a magnitude of 8 to 9 occurring within the next 30 years is estimated to be 70 to 80%. At Hotron, we recommend the introduction of seismic devices for earthquake countermeasures in buildings and equipment. The seismic device 'HK-2' is a product that automatically performs various controls that have been pre-set when it detects strong shaking equivalent to a seismic intensity of 5 lower or higher. For example, it can automatically execute actions such as: "Open automatic doors and gates to secure evacuation routes and access for emergency vehicles" "Transmit signals to the control room and stop facility equipment" "Unlock the keys to locked lockers" "Automatically play voice guidance" For more details, please download the materials or contact us.

The "HA-T Series" is an energy-saving automatic door sensor that opens only for those who want to enter, whether on a busy street or in a narrow passageway. The automatic door opens simply by bringing your hand close, addressing hygiene concerns even in facilities used by a large number of people. Depending on the application and installation location, you can choose between "Non-vision Mount Type/HA-T401" and "Non-vision Built-in Type/HA-T520." 【Recommended for such places!】 ☑ Entrance facing a busy passageway ☑ Presence of counters or signs near the door ☑ Buildings facing narrow passageways ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors 【Features】 ● Adaptable to various door types with four detection spot settings ● Reduces unnecessary opening and closing to minimize power consumption, contributing to energy-saving effects ● Equipped with a light touch function, allowing the door to open and close simply by waving your hand, ensuring hygiene ● Can also be used as a wide detection range non-vision infrared sensor ◎ For more details, please download the materials or contact us.

Seven Corporation has begun research and development related to rust prevention, aiming to expand the functionality of the natural multifunctional aqueous solution "SEA'S 7." This research is being promoted as a collaborative study with the Industrial Technology Research Institute. In recent years, the manufacturing industry has been seeking technologies that balance environmental impact reduction and improved work safety, making rust prevention measures after cleaning a critical issue. This research includes corrosion evaluation using metal test pieces, measurement of weight changes, and durability tests in a circulating water environment, advancing the understanding of rust prevention mechanisms and performance evaluation. In the future, we aim to develop a next-generation SEA'S 7 that incorporates rust prevention functionality in addition to cleaning, disinfection, and deodorization, contributing to the efficiency of manufacturing processes and the reduction of environmental impact.

We are pleased to announce the launch of the "Vertical Aluminum Step Type F." The "Vertical Aluminum Step Type F" is a new type of aluminum ladder specifically designed for excavation sites, based on the existing "Vertical Aluminum Step." The vertical aluminum step is lightweight due to its aluminum construction, making it easy to transport and set up. Additionally, its modular design allows for flexible height combinations (with connecting parts of 0.7m, 1.0m, and 2.0m). The newly launched Type F retains the features of the previous model while providing even greater convenience. <Features of Type F> ■ The hook adjustment range of the fixed part has been expanded. It can be attached to structures ranging from 20mm to 200mm. ■ The length of the stand pipe can be adjusted. The stand pipe can be stored, making transportation and storage easier. <Release Date> January 5, 2026 <Specifications> - Standard set for Type F: 2.4m *Individual sales of the hanging fixed part and connecting parts are available. *Sales of the previous model (stand pipe fixed type) will also continue.